Mitsubishi Electronics SDP-ECO 1630 III manual Refer to 4.1 Cable

Page 29

Chapter 3 Handling Plates

Turn the nip roller

Gently insert the plate. clearance handle until it is horizontal.

Confirm that there is no gap between the plate roll and the spool plate and that the set screw is placed in the correct position and then tighten the set screw.

6)Turn ON the power switch to the main unit. After completion of the initialization process, grab the handle on the right side, open the magazine cover, and load a plate roll which has been mounted on a spool shaft.

Note

Refer to "4.1 Cable

 

connection check", "4.2

 

Turning ON the power

 

switch" and "4.3

 

Initialization" in Chapter 4

 

"Operation" when turning

 

ON the main power

 

switch.

7)Put the spool shaft holder on the spool set guide and set the guide into the SDP-Eco 1630 III.

Position the shaft with its red mark toward the back of the machine (on the right side).

8)Turn the nip roller clearance handle (located at the panel bottom) until it is horizontal. This cancels the main roller nipping.

Gently insert the plate into the clearance in the guide roller.

- 21 -

Image 29
Contents Page III For Your Safety Compliance with Cispr Rules When export the machineCompliance with FCC Rules Limit of responsibilityIntroductory Note About this manual Contents Menus and panel displays When using the machine On SafetyPower supply Maintenance and safe passage during emergenciesSafety switches This machine incorporates a power supply unitSDP-Eco 1630 III is equipped with a leakage circuit breaker This machine incorporates high current electrical circuitsFor European model Hazard Safe handling method Types of warning labelsLocations of the machines warning labels are shown below Handling processing chemicals Processing chemical components Power cables Before connecting the power cableUnacceptable Operation precautionsSDP-Eco 1630 III Installation Precautions during transport and installationTransport and installation Installation environmentVentilation Installation space MaintenanceMachine disposal Page Main unit Names of Machine Components and PartsPage Operation panel Safety switch Handling plates Plate settingTwo set screws are Refer to 4.1 Cable Insert the plate edge until Plate end processing Page Cable connection check OperationPanel display flow after machine startup Turning on the power switchInitialization Press the Menu Key to display Amount using the key or Key and register the value with Local exposure ExposureRemote exposure Exposure Processing chemical replenishment Processor sectionPreparing and pouring processing chemical Preparing rinse water Processing chemical replacementIf the machine is not used for a long period Handling waste liquidCollecting exposed plates Turning OFF the power supply and inspection at shutdownOperation Page User menu Menus and panel displaysOperation status Remote mode display Power ON/OFF keyMenu/command selection Panel operationCommand execution Switch the mode between remote and localShift between commands Example Plate data User menuData channel Plate typeLaser setting Resolution settingLaser menu Remaining amount of plateLaser test exposure Punch specifications Mode menuPre. Feed menu Image Data menuRinse Maintenance menuKey Procedure In cases where the current values are changed toReplacement procedure MaintenanceCutter blade replacement Dust, clean it off with a blower Cylindrical lens cleaningFilter cleaning Punch dust removal Cleaning the processor rack Cleaning the processor sectionResetting the punch counter Processor rack Stay Re-attach the supply guides to the processor rack Cleaning the processing chemical tank and filterCleaning the processing chemical supply pipe Cleaning the nip roller and exit roller Upper Cleaning the exit roller lower Set screw Roller fixing bracket Washing tank Bearing for a roller Exit roller lower Cleaning the washing tank Left tray rail Set screw Around when you remove the hose Slide the washing tank Replacing the diffusion sheet SLM-EAC, SLM-EST Put the accompanying diffusion List of expendable parts How to order partsMonth Year SDP-Eco 1630 III Maintenance and Inspection Chart Message Displaying and clearing errorsMessage Message Operation status Status displayMessage Error contents List of error messagesME9 Removing Plate jam 1 Jam removal procedureRemoving Plate jam Basic specifications SpecificationsOverview diagram Silver Digiplater