Mitsubishi Electronics SDP-ECO 1630 III manual Switch the mode between remote and local

Page 48

SDP-Eco1630 III USERS MANUAL

•Switch the mode between remote and local

Remote Mode

Local Mode

Start OK

<Plate Data>

•Shift between commands (Example)

1st hierarchy

<Maintenance>

2nd hierarchy Cutter Processor>

•Command execution

<Ver SCSI-ID>

There are two types of commands: one which activates machine functions such as preliminary feeding and cutter-processor commands, and one which is used, for example, to set numerical values.

For commands in which numerical values can be changed (Example: Referring to P27 "4.4 Data input for the set plate")

Use the to move the cursor to the numerical value display. Press the

key to start the display flashing and change the displayed value. (In some modes the numerical value display starts flashing from the time it is first displayed.)

The or key increases/decreases a numerical value.

Press the key when the desired number appears.

If you wish to reset a value or interrupt the setting procedure, press the key to return to the upper menu level without changing the currently set value and re-start the setting procedure from the beginning by selecting the same command.

For commands in which numerical values can not be changed (Example: Referring to P28 "4.5 Execution of Pre. Feed command")

Use the to select the desired command. Then press the key to execute it.

Repeatedly press the key until Start OK is displayed to return to the on- line mode.

- 40 -

Image 48

Contents Page III For Your Safety When export the machine Compliance with Cispr RulesCompliance with FCC Rules Limit of responsibilityIntroductory Note About this manual Contents Menus and panel displays On Safety When using the machinePower supply Maintenance and safe passage during emergenciesThis machine incorporates a power supply unit Safety switchesSDP-Eco 1630 III is equipped with a leakage circuit breaker This machine incorporates high current electrical circuitsFor European model Types of warning labels Hazard Safe handling methodLocations of the machines warning labels are shown below Handling processing chemicals Processing chemical components Before connecting the power cable Power cablesOperation precautions UnacceptablePrecautions during transport and installation SDP-Eco 1630 III InstallationTransport and installation Installation environmentVentilation Maintenance Installation spaceMachine disposal Page Names of Machine Components and Parts Main unitPage Operation panel Safety switch Plate setting Handling platesTwo set screws are Refer to 4.1 Cable Insert the plate edge until Plate end processing Page Operation Cable connection checkTurning on the power switch InitializationPanel display flow after machine startup Press the Menu Key to display Amount using the key or Key and register the value with Exposure Remote exposureLocal exposure Exposure Processor section Preparing and pouring processing chemicalProcessing chemical replenishment Processing chemical replacement Preparing rinse waterHandling waste liquid If the machine is not used for a long periodTurning OFF the power supply and inspection at shutdown Collecting exposed platesOperation Page Menus and panel displays User menuOperation status Power ON/OFF key Remote mode displayMenu/command selection Panel operationSwitch the mode between remote and local Shift between commands ExampleCommand execution User menu Plate dataData channel Plate typeResolution setting Laser settingLaser menu Remaining amount of plateLaser test exposure Mode menu Punch specificationsPre. Feed menu Image Data menuMaintenance menu RinseProcedure In cases where the current values are changed to KeyMaintenance Cutter blade replacementReplacement procedure Cylindrical lens cleaning Dust, clean it off with a blowerFilter cleaning Punch dust removal Cleaning the processor section Resetting the punch counterCleaning the processor rack Processor rack Stay Cleaning the processing chemical tank and filter Re-attach the supply guides to the processor rackCleaning the processing chemical supply pipe Cleaning the nip roller and exit roller Upper Cleaning the exit roller lower Set screw Roller fixing bracket Washing tank Bearing for a roller Exit roller lower Cleaning the washing tank Left tray rail Set screw Around when you remove the hose Slide the washing tank Replacing the diffusion sheet SLM-EAC, SLM-EST Put the accompanying diffusion How to order parts List of expendable partsMonth Year SDP-Eco 1630 III Maintenance and Inspection Chart Displaying and clearing errors MessageMessage Status display Message Operation statusList of error messages Message Error contentsME9 Jam removal procedure Removing Plate jam 1Removing Plate jam Specifications Basic specificationsOverview diagram Silver Digiplater