Mitsubishi Electronics SDP-ECO 1630 III manual Operation, Cable connection check

Page 33

Chapter 4 Operation

Chapter 4 Operation

The SDP-Eco 1630 III is a SCSI device. Turn ON the power switch for this machine first, and complete its initialization routine. Then turn ON the power switch to the host computer (RIP computer).

Be sure to turn OFF the power switch to the host computer (RIP computer) when turning OFF the power switch for this machine.

Never open the front door or plate setting cover unnecessarily. Do not open the plate setting cover except when replacing the plate roll.

Caution Otherwise, the plate being processed may be adversely exposed. If the front door is opened while the plate is being fed, it will adversely affect the plate's image quality and feed state.

Do not open the cover during operation

Do not open the door during operation

4.1 Cable connection check

After checking that the entire system including the host computer (RIP computer) is shut down, check that all cables are connected correctly. The figure below shows cable connections and locations. The cables used here should be SCSI connection dedicated cables.

Wide SCSI connector

Do not use cables other than the provided SCSI cables.

If the cable must be extended, please purchase the optional differential unit. This ma- chine is incorporated with an active terminator, so that this differential unit can be mounted internally.

- 25 -

Image 33

Contents Page III For Your Safety Compliance with Cispr Rules When export the machineCompliance with FCC Rules Limit of responsibilityIntroductory Note About this manual Contents Menus and panel displays When using the machine On SafetyPower supply Maintenance and safe passage during emergenciesSafety switches This machine incorporates a power supply unitSDP-Eco 1630 III is equipped with a leakage circuit breaker This machine incorporates high current electrical circuitsFor European model Hazard Safe handling method Types of warning labelsLocations of the machines warning labels are shown below Handling processing chemicals Processing chemical components Power cables Before connecting the power cableUnacceptable Operation precautionsSDP-Eco 1630 III Installation Precautions during transport and installationTransport and installation Installation environmentVentilation Installation space MaintenanceMachine disposal Page Main unit Names of Machine Components and PartsPage Operation panel Safety switch Handling plates Plate settingTwo set screws are Refer to 4.1 Cable Insert the plate edge until Plate end processing Page Cable connection check OperationTurning on the power switch InitializationPanel display flow after machine startup Press the Menu Key to display Amount using the key or Key and register the value with Exposure Remote exposureLocal exposure Exposure Processor section Preparing and pouring processing chemicalProcessing chemical replenishment Preparing rinse water Processing chemical replacementIf the machine is not used for a long period Handling waste liquidCollecting exposed plates Turning OFF the power supply and inspection at shutdownOperation Page User menu Menus and panel displaysOperation status Remote mode display Power ON/OFF keyMenu/command selection Panel operationSwitch the mode between remote and local Shift between commands ExampleCommand execution Plate data User menuData channel Plate typeLaser setting Resolution settingLaser menu Remaining amount of plateLaser test exposure Punch specifications Mode menuPre. Feed menu Image Data menuRinse Maintenance menuKey Procedure In cases where the current values are changed toMaintenance Cutter blade replacementReplacement procedure Dust, clean it off with a blower Cylindrical lens cleaningFilter cleaning Punch dust removal Cleaning the processor section Resetting the punch counterCleaning the processor rack Processor rack Stay Re-attach the supply guides to the processor rack Cleaning the processing chemical tank and filterCleaning the processing chemical supply pipe Cleaning the nip roller and exit roller Upper Cleaning the exit roller lower Set screw Roller fixing bracket Washing tank Bearing for a roller Exit roller lower Cleaning the washing tank Left tray rail Set screw Around when you remove the hose Slide the washing tank Replacing the diffusion sheet SLM-EAC, SLM-EST Put the accompanying diffusion List of expendable parts How to order partsMonth Year SDP-Eco 1630 III Maintenance and Inspection Chart Displaying and clearing errors MessageMessage Message Operation status Status displayMessage Error contents List of error messagesME9 Removing Plate jam 1 Jam removal procedureRemoving Plate jam Basic specifications SpecificationsOverview diagram Silver Digiplater