Mitsubishi Electronics SDP-ECO 1630 III manual List of error messages, Message Error contents

Page 77

Chapter 8 Message

8.5 List of error messages

The following is a list of error messages, and steps that can be taken.

Message

Error contents

 

 

 

Serial error

An internal communication error occurred. Re-boot the

 

machine.

 

 

 

If this error occurs frequently, please contact the dealer

 

where you purchased this machine.

 

 

 

 

JAM1

The plate is jammed.

Remove the plate following the

 

jam removal procedure.

 

 

 

 

 

JAM2

The plate is jammed.

Remove the plate following the

 

jam removal procedure.

 

 

 

 

 

JAM3

The plate is jammed.

Remove the plate following the

 

jam removal procedure.

 

 

 

 

I/F error1

A SCSI communication error occurred. Re-boot the

 

machine. If this error occurs frequently, please contact

 

the dealer where you purchased this machine.

 

 

 

ME1

The cutter does not return to its initial position. Turn ON

 

the power switch again.

 

 

 

 

ME2

The cutter is not located at its initial position. Turn ON

 

the power switch again.

 

 

 

 

 

ME3 Nip free

The nip roller is open.

Close the nip roller clearance

 

handle.

 

 

 

 

ME4

An internal communication error occurred in the

 

machine. If this error occurs frequently, please contact

 

the dealer where you purchased this machine.

 

 

 

ME5

An internal communication error occurred. Re-boot the

 

machine.

 

 

 

If this error occurs frequently, please contact the dealer

 

where you purchased this machine.

 

 

 

ME6

The laser does not light. It may be caused by low laser,

 

but if it occurs even after you boost the laser, please

 

contact the dealer where you purchased this machine.

 

 

 

ME7

A problem occurred in the polygon mirror.

Please

 

contact the dealer where you purchased this machine.

 

 

 

ME8

A problem occurred in the processor heater.

Please

 

contact the dealer where you purchased this machine.

 

 

 

 

- 69 -

Image 77
Contents Page III For Your Safety Compliance with Cispr Rules When export the machineCompliance with FCC Rules Limit of responsibilityIntroductory Note About this manual Contents Menus and panel displays When using the machine On SafetyPower supply Maintenance and safe passage during emergenciesSafety switches This machine incorporates a power supply unitSDP-Eco 1630 III is equipped with a leakage circuit breaker This machine incorporates high current electrical circuitsFor European model Hazard Safe handling method Types of warning labelsLocations of the machines warning labels are shown below Handling processing chemicals Processing chemical components Power cables Before connecting the power cableUnacceptable Operation precautionsSDP-Eco 1630 III Installation Precautions during transport and installationTransport and installation Installation environmentVentilation Installation space MaintenanceMachine disposal Page Main unit Names of Machine Components and PartsPage Operation panel Safety switch Handling plates Plate settingTwo set screws are Refer to 4.1 Cable Insert the plate edge until Plate end processing Page Cable connection check OperationPanel display flow after machine startup Turning on the power switchInitialization Press the Menu Key to display Amount using the key or Key and register the value with Local exposure ExposureRemote exposure Exposure Processing chemical replenishment Processor sectionPreparing and pouring processing chemical Preparing rinse water Processing chemical replacementIf the machine is not used for a long period Handling waste liquidCollecting exposed plates Turning OFF the power supply and inspection at shutdownOperation Page User menu Menus and panel displaysOperation status Remote mode display Power ON/OFF keyMenu/command selection Panel operationCommand execution Switch the mode between remote and localShift between commands Example Plate data User menuData channel Plate typeLaser setting Resolution settingLaser menu Remaining amount of plateLaser test exposure Punch specifications Mode menuPre. Feed menu Image Data menuRinse Maintenance menuKey Procedure In cases where the current values are changed toReplacement procedure MaintenanceCutter blade replacement Dust, clean it off with a blower Cylindrical lens cleaningFilter cleaning Punch dust removal Cleaning the processor rack Cleaning the processor sectionResetting the punch counter Processor rack Stay Re-attach the supply guides to the processor rack Cleaning the processing chemical tank and filterCleaning the processing chemical supply pipe Cleaning the nip roller and exit roller Upper Cleaning the exit roller lower Set screw Roller fixing bracket Washing tank Bearing for a roller Exit roller lower Cleaning the washing tank Left tray rail Set screw Around when you remove the hose Slide the washing tank Replacing the diffusion sheet SLM-EAC, SLM-EST Put the accompanying diffusion List of expendable parts How to order partsMonth Year SDP-Eco 1630 III Maintenance and Inspection Chart Message Displaying and clearing errorsMessage Message Operation status Status displayMessage Error contents List of error messagesME9 Removing Plate jam 1 Jam removal procedureRemoving Plate jam Basic specifications SpecificationsOverview diagram Silver Digiplater