Mitsubishi Electronics SDP-ECO 1630 III manual Handling processing chemicals

Page 14

SDP-Eco1630 III USERS MANUAL

Chapter 1 On Safety

1.3 Handling processing chemicals

The SDP-Eco 1630 III uses processing chemicals to activate and stabilize exposed plates. The processing chemicals used in this Warning machine are not generally dangerous to humans, but failure to use them in the correct manner is dangerous. Be sure to handle all

processing chemicals with care.

Cautions for use of processing chemicals

Inflammation may occur if processing chemicals come in contact

with the eyes or skin, so be sure to wear protective gear (safety Caution goggles and rubber gloves) when handling the chemicals.

Keep out of reach of children.

What to do in case of emergency

If chemicals come in contact with the eyes, immediately rinse with clean running water for at least 15 minutes. If the inflammation persists, consult an eye specialist.

Caution If chemicals come in contact with the skin, immediately rinse under clean running water.

If chemicals are swallowed, immediately consult a physician. Report the ingredients of the chemical or solution to the physician.

Cautions for handling waste chemicals

These chemicals have high COD and pH levels (especially the activator) and cannot be disposed of by simply pouring them down Caution the drain. Please have processing chemicals removed by a

certified waste management specialist.

- 6 -

Image 14

Contents Page III For Your Safety Compliance with FCC Rules When export the machineCompliance with Cispr Rules Limit of responsibilityIntroductory Note About this manual Contents Menus and panel displays Power supply On SafetyWhen using the machine Maintenance and safe passage during emergenciesSDP-Eco 1630 III is equipped with a leakage circuit breaker This machine incorporates a power supply unitSafety switches This machine incorporates high current electrical circuitsFor European model Types of warning labels Hazard Safe handling methodLocations of the machines warning labels are shown below Handling processing chemicals Processing chemical components Before connecting the power cable Power cablesOperation precautions UnacceptableTransport and installation Precautions during transport and installationSDP-Eco 1630 III Installation Installation environmentVentilation Maintenance Installation spaceMachine disposal Page Names of Machine Components and Parts Main unitPage Operation panel Safety switch Plate setting Handling platesTwo set screws are Refer to 4.1 Cable Insert the plate edge until Plate end processing Page Operation Cable connection checkPanel display flow after machine startup Turning on the power switchInitialization Press the Menu Key to display Amount using the key or Key and register the value with Local exposure ExposureRemote exposure Exposure Processing chemical replenishment Processor sectionPreparing and pouring processing chemical Processing chemical replacement Preparing rinse waterHandling waste liquid If the machine is not used for a long periodTurning OFF the power supply and inspection at shutdown Collecting exposed platesOperation Page Menus and panel displays User menuOperation status Menu/command selection Power ON/OFF keyRemote mode display Panel operationCommand execution Switch the mode between remote and localShift between commands Example Data channel User menuPlate data Plate typeLaser menu Resolution settingLaser setting Remaining amount of plateLaser test exposure Pre. Feed menu Mode menuPunch specifications Image Data menuMaintenance menu RinseProcedure In cases where the current values are changed to KeyReplacement procedure MaintenanceCutter blade replacement Cylindrical lens cleaning Dust, clean it off with a blowerFilter cleaning Punch dust removal Cleaning the processor rack Cleaning the processor sectionResetting the punch counter Processor rack Stay Cleaning the processing chemical tank and filter Re-attach the supply guides to the processor rackCleaning the processing chemical supply pipe Cleaning the nip roller and exit roller Upper Cleaning the exit roller lower Set screw Roller fixing bracket Washing tank Bearing for a roller Exit roller lower Cleaning the washing tank Left tray rail Set screw Around when you remove the hose Slide the washing tank Replacing the diffusion sheet SLM-EAC, SLM-EST Put the accompanying diffusion How to order parts List of expendable partsMonth Year SDP-Eco 1630 III Maintenance and Inspection Chart Message Displaying and clearing errorsMessage Status display Message Operation statusList of error messages Message Error contentsME9 Jam removal procedure Removing Plate jam 1Removing Plate jam Specifications Basic specificationsOverview diagram Silver Digiplater