Mitsubishi Electronics SDP-ECO 1630 III manual For Your Safety

Page 3

For Your Safety

-This manual must be thoroughly read and understood by all operators before they attempt to use SDP-Eco 1630 III.

-This manual provides general guidelines, precautions and warnings for the safe operation of this machine. Very serious accidents may occur if this machine is utilized without following this manual and we shall bear absolutely no liability or responsibility for the consequences.

-The warning labels for hazard prevention area attached to dangerous parts or areas of the machine. Study and understand all the specific dangers involved and how they can be avoided.

-Keep this manual available and near the machine at all times so that it can be immediately referred to whenever necessary.

-Look up the name, address and phone number of our nearest dealer or branch office (listed on the back page of this manual), and post the information prominently for quick reference.

-Please make sure that this manual reaches everyone charged with operating this machine.

Warning

Machine operators must thoroughly read Chapter 1. Do not turn on the machine's power supply until all of the precautions have been read and understood. Very serious accidents may occur if this instruction is not observed.

Administrators and supervisors shall not instruct anyone to operate or inspect the SDP- Eco 1630 III unless he/she is familiar with all the contents of this document.

i

Image 3

Contents Page III For Your Safety Limit of responsibility When export the machineCompliance with Cispr Rules Compliance with FCC RulesIntroductory Note About this manual Contents Menus and panel displays Maintenance and safe passage during emergencies On SafetyWhen using the machine Power supplyThis machine incorporates high current electrical circuits This machine incorporates a power supply unitSafety switches SDP-Eco 1630 III is equipped with a leakage circuit breakerFor European model Hazard Safe handling method Types of warning labelsLocations of the machines warning labels are shown below Handling processing chemicals Processing chemical components Power cables Before connecting the power cableUnacceptable Operation precautionsInstallation environment Precautions during transport and installationSDP-Eco 1630 III Installation Transport and installationVentilation Installation space MaintenanceMachine disposal Page Main unit Names of Machine Components and PartsPage Operation panel Safety switch Handling plates Plate settingTwo set screws are Refer to 4.1 Cable Insert the plate edge until Plate end processing Page Cable connection check OperationTurning on the power switch InitializationPanel display flow after machine startup Press the Menu Key to display Amount using the key or Key and register the value with Exposure Remote exposureLocal exposure Exposure Processor section Preparing and pouring processing chemicalProcessing chemical replenishment Preparing rinse water Processing chemical replacementIf the machine is not used for a long period Handling waste liquidCollecting exposed plates Turning OFF the power supply and inspection at shutdownOperation Page User menu Menus and panel displaysOperation status Panel operation Power ON/OFF keyRemote mode display Menu/command selectionSwitch the mode between remote and local Shift between commands ExampleCommand execution Plate type User menuPlate data Data channelRemaining amount of plate Resolution settingLaser setting Laser menuLaser test exposure Image Data menu Mode menuPunch specifications Pre. Feed menuRinse Maintenance menuKey Procedure In cases where the current values are changed toMaintenance Cutter blade replacementReplacement procedure Dust, clean it off with a blower Cylindrical lens cleaningFilter cleaning Punch dust removal Cleaning the processor section Resetting the punch counterCleaning the processor rack Processor rack Stay Re-attach the supply guides to the processor rack Cleaning the processing chemical tank and filterCleaning the processing chemical supply pipe Cleaning the nip roller and exit roller Upper Cleaning the exit roller lower Set screw Roller fixing bracket Washing tank Bearing for a roller Exit roller lower Cleaning the washing tank Left tray rail Set screw Around when you remove the hose Slide the washing tank Replacing the diffusion sheet SLM-EAC, SLM-EST Put the accompanying diffusion List of expendable parts How to order partsMonth Year SDP-Eco 1630 III Maintenance and Inspection Chart Displaying and clearing errors MessageMessage Message Operation status Status displayMessage Error contents List of error messagesME9 Removing Plate jam 1 Jam removal procedureRemoving Plate jam Basic specifications SpecificationsOverview diagram Silver Digiplater