Mitsubishi Electronics Mitsubishi SDP-ECO 1630 III Platemaker: Chemical Replacement and Rinse Water Preparation Guide

Page 40

SDP-Eco1630 III USERS MANUAL

Processing chemical replacement

Replace the processing chemical every three months regardless of the number of plates processed.

Preparing rinse water

1)Pour approximately 1 liter of water into the rinse water replenisher bottle and set it in the washing tank.

2)Always make sure that the bottle is filled with water before turning ON the power switch.

3)After turning ON the power, reset the counter in the <Rinse> menu with the following operation.

[Procedure]

 

 

 

 

(1)

Push the MENU

key to display

 

.

 

< Plate Data >

 

(2)

Select

 

using the

key, and then push the ￿￿￿￿key.

<Rinse>

 

 

 

key, align the cursor to "CLR" in the

 

 

 

￿￿￿￿

Count 150 CLR

(3) Using the

 

 

menu.

 

 

 

 

(4)

Push the

key to reset the counter.

 

Caution

If the washing tank becomes empty of water, this will adversely affect the plate's image quality. Replenish the rinse water everyday before starting operation.

Replace the water in the washing tank every month. Replacement frequency may vary depending on the quality of the water and the season.

Confirming the remaining amount of rinse water and replenishment

When the rinse water is running out and needs to be replenished, the "Rinse Tank Check" message appears in the display, causing the buzzer to sound. Confirm the remaining amount of rinse water and replenish it as necessary.

1)Press the key to turn the buzzer OFF.

2)Open the front door.

3)Remove the rinse water replenishing bottle and replenish it with rinse water.

4)Return the rinse water replenishing bottle to its original position, and then close the front door.

Note

-Pressing the key to delete the above message in the display does not reset the software counter, causing the message to appear in the display and

the buzzer to sound a while after the key has been pressed. To reset the counter, open the front door, and then confirm the remaining amount of rinse

water, or display the <Rinse> window in the users menu, and then perform a counter clearance operation. (For detailed operation, refer to the section "Preparing Rinse Water.")

- 32 -

Image 40
Contents Page III For Your Safety When export the machine Compliance with Cispr RulesCompliance with FCC Rules Limit of responsibilityIntroductory Note About this manual Contents Menus and panel displays On Safety When using the machinePower supply Maintenance and safe passage during emergenciesThis machine incorporates a power supply unit Safety switchesSDP-Eco 1630 III is equipped with a leakage circuit breaker This machine incorporates high current electrical circuitsFor European model Types of warning labels Hazard Safe handling methodLocations of the machines warning labels are shown below Handling processing chemicals Processing chemical components Before connecting the power cable Power cablesOperation precautions UnacceptablePrecautions during transport and installation SDP-Eco 1630 III InstallationTransport and installation Installation environmentVentilation Maintenance Installation spaceMachine disposal Page Names of Machine Components and Parts Main unitPage Operation panel Safety switch Plate setting Handling platesTwo set screws are Refer to 4.1 Cable Insert the plate edge until Plate end processing Page Operation Cable connection checkInitialization Turning on the power switchPanel display flow after machine startup Press the Menu Key to display Amount using the key or Key and register the value with Remote exposure ExposureLocal exposure Exposure Preparing and pouring processing chemical Processor sectionProcessing chemical replenishment Processing chemical replacement Preparing rinse waterHandling waste liquid If the machine is not used for a long periodTurning OFF the power supply and inspection at shutdown Collecting exposed platesOperation Page Menus and panel displays User menuOperation status Power ON/OFF key Remote mode displayMenu/command selection Panel operationShift between commands Example Switch the mode between remote and localCommand execution User menu Plate dataData channel Plate typeResolution setting Laser settingLaser menu Remaining amount of plateLaser test exposure Mode menu Punch specificationsPre. Feed menu Image Data menuMaintenance menu RinseProcedure In cases where the current values are changed to KeyCutter blade replacement MaintenanceReplacement procedure Cylindrical lens cleaning Dust, clean it off with a blowerFilter cleaning Punch dust removal Resetting the punch counter Cleaning the processor sectionCleaning the processor rack Processor rack Stay Cleaning the processing chemical tank and filter Re-attach the supply guides to the processor rackCleaning the processing chemical supply pipe Cleaning the nip roller and exit roller Upper Cleaning the exit roller lower Set screw Roller fixing bracket Washing tank Bearing for a roller Exit roller lower Cleaning the washing tank Left tray rail Set screw Around when you remove the hose Slide the washing tank Replacing the diffusion sheet SLM-EAC, SLM-EST Put the accompanying diffusion How to order parts List of expendable partsMonth Year SDP-Eco 1630 III Maintenance and Inspection Chart Message Displaying and clearing errorsMessage Status display Message Operation statusList of error messages Message Error contentsME9 Jam removal procedure Removing Plate jam 1Removing Plate jam Specifications Basic specificationsOverview diagram Silver Digiplater