Mitsubishi Electronics SDP-ECO 1630 III manual Key

Page 54

SDP-Eco1630 III USERS MANUAL

•The alarm function in this machine has been set to OFF before shipment at the factory.

(Settings 000 = OFF)

•The consumption rate of rinse water may be different depending on the settings in the machine. Set the consumption rate with the following procedure.

[Procedure] (In cases where the current values are changed to "150".)

(1) Push the MENU key to display the

< Plate Data >

window.

(2)

Select

< Rinse >

 

with the

key, and then push the

￿￿￿￿key.

(3)

When

 

 

 

 

 

 

 

 

 

Count 150 CLR

 

 

￿￿￿￿

 

 

 

 

 

 

is displayed, make sure that the cursor is placed

 

under the setting, and then push the

 

key.

 

(4)

Push either the

 

key (Increase) or the

key (Decrease) to set the

(5)

settings to "150".

 

 

￿￿￿￿

key to confirm the setting.

After changing the setting, push the

 

(6)

Push the MENU key two times to display the

 

window.

< Plate Data >

Note

Use "120 to 160" as a reference value. Adjust the rate of rinse water reduction depending on the installation conditions of the machine.

(Adjustable range: 50 to 300. Note that using "000" deactivates this function.)

[Notes for adjustment]

(1)When the "Rinse Tank Check" message is displayed. If the replenishing bottle is empty, decrease the setting.

If there is a lot of rinse water left in the bottle, increase the setting.

(2)To deactivate the software counter function, use "000" as a setting value. Be sure to reset the counter by "CLR" after you have adjusted the setting.

- 46 -

Page 53 Page 55
Image 54
Page 53 Page 55
Contents Page III For Your Safety Compliance with FCC Rules When export the machineCompliance with Cispr Rules Limit of responsibilityIntroductory Note About this manual Contents Menus and panel displays Power supply On SafetyWhen using the machine Maintenance and safe passage during emergenciesSDP-Eco 1630 III is equipped with a leakage circuit breaker This machine incorporates a power supply unitSafety switches This machine incorporates high current electrical circuitsFor European model Types of warning labels Hazard Safe handling methodLocations of the machines warning labels are shown below Handling processing chemicals Processing chemical components Before connecting the power cable Power cablesOperation precautions UnacceptableTransport and installation Precautions during transport and installationSDP-Eco 1630 III Installation Installation environmentVentilation Maintenance Installation spaceMachine disposal Page Names of Machine Components and Parts Main unitPage Operation panel Safety switch Plate setting Handling platesTwo set screws are Refer to 4.1 Cable Insert the plate edge until Plate end processing Page Operation Cable connection checkTurning on the power switch InitializationPanel display flow after machine startup Press the Menu Key to display Amount using the key or Key and register the value with Exposure Remote exposureLocal exposure Exposure Processor section Preparing and pouring processing chemicalProcessing chemical replenishment Processing chemical replacement Preparing rinse waterHandling waste liquid If the machine is not used for a long periodTurning OFF the power supply and inspection at shutdown Collecting exposed platesOperation Page Menus and panel displays User menuOperation status Menu/command selection Power ON/OFF keyRemote mode display Panel operationSwitch the mode between remote and local Shift between commands ExampleCommand execution Data channel User menuPlate data Plate typeLaser menu Resolution settingLaser setting Remaining amount of plateLaser test exposure Pre. Feed menu Mode menuPunch specifications Image Data menuMaintenance menu RinseProcedure In cases where the current values are changed to KeyMaintenance Cutter blade replacementReplacement procedure Cylindrical lens cleaning Dust, clean it off with a blowerFilter cleaning Punch dust removal Cleaning the processor section Resetting the punch counterCleaning the processor rack Processor rack Stay Cleaning the processing chemical tank and filter Re-attach the supply guides to the processor rackCleaning the processing chemical supply pipe Cleaning the nip roller and exit roller Upper Cleaning the exit roller lower Set screw Roller fixing bracket Washing tank Bearing for a roller Exit roller lower Cleaning the washing tank Left tray rail Set screw Around when you remove the hose Slide the washing tank Replacing the diffusion sheet SLM-EAC, SLM-EST Put the accompanying diffusion How to order parts List of expendable partsMonth Year SDP-Eco 1630 III Maintenance and Inspection Chart Displaying and clearing errors MessageMessage Status display Message Operation statusList of error messages Message Error contentsME9 Jam removal procedure Removing Plate jam 1Removing Plate jam Specifications Basic specificationsOverview diagram Silver Digiplater
Top Page Image Contents