Mitsubishi Electronics SDP-ECO 1630 III manual Cylindrical lens cleaning

Page 56

SDP-Eco1630 III USERS MANUAL

7.2 Cylindrical lens cleaning

	The SDP-Eco 1630 III incorporates a
	highly accurate optical system in
Screw	which the lens is positioned
	extremely close to the exposed
	surface.
	Therefore, if the lens is soiled with
	dirt or dust due to environmental
	conditions, for example, it may show
	up as a vertical line (white or black).
	1)If a vertical line appears, open the
	front door, loosen the two screws on
	the cylindrical lens unit, and remove
	the entire unit by gently pulling it out
	toward the operator.
Remove the 2)Inspect the lens under a bright
entire unit	fluorescent light to check its
by gently	cleanliness and, if there is any dirt or
pulling it out	cleanliness and, if there is any dirt or

	toward the	dust, clean it off with a blower.
	operator.	dust, clean it off with a blower.
	operator.

Cylindrical lens unit

Caution

Do not use compressed air when cleaning the lens.

Cylindrical lens

Clean it off with a blower

3)Never touch the lens with your hand or any kind of tool. These lens can be easily scratched and may require replacement.

Caution The plate will be fogged after you replace the lens. Before the next operation, feed one sheet through the machine.

4)Re-assemble the cylindrical lens unit, reversing the previous procedure. Be sure to firmly re-insert the unit as far back as it will go into the machine chassis.

- 48 -

Image 56

Contents Page III For Your Safety When export the machine Compliance with Cispr RulesCompliance with FCC Rules Limit of responsibilityIntroductory Note About this manual Contents Menus and panel displays On Safety When using the machinePower supply Maintenance and safe passage during emergenciesThis machine incorporates a power supply unit Safety switchesSDP-Eco 1630 III is equipped with a leakage circuit breaker This machine incorporates high current electrical circuitsFor European model Types of warning labels Hazard Safe handling methodLocations of the machines warning labels are shown below Handling processing chemicals Processing chemical components Before connecting the power cable Power cablesOperation precautions UnacceptablePrecautions during transport and installation SDP-Eco 1630 III InstallationTransport and installation Installation environmentVentilation Maintenance Installation spaceMachine disposal Page Names of Machine Components and Parts Main unitPage Operation panel Safety switch Plate setting Handling platesTwo set screws are Refer to 4.1 Cable Insert the plate edge until Plate end processing Page Operation Cable connection checkPanel display flow after machine startup Turning on the power switchInitialization Press the Menu Key to display Amount using the key or Key and register the value with Local exposure ExposureRemote exposure Exposure Processing chemical replenishment Processor sectionPreparing and pouring processing chemical Processing chemical replacement Preparing rinse waterHandling waste liquid If the machine is not used for a long periodTurning OFF the power supply and inspection at shutdown Collecting exposed platesOperation Page Menus and panel displays User menuOperation status Power ON/OFF key Remote mode displayMenu/command selection Panel operationCommand execution Switch the mode between remote and localShift between commands Example User menu Plate dataData channel Plate typeResolution setting Laser settingLaser menu Remaining amount of plateLaser test exposure Mode menu Punch specificationsPre. Feed menu Image Data menuMaintenance menu RinseProcedure In cases where the current values are changed to KeyReplacement procedure MaintenanceCutter blade replacement Cylindrical lens cleaning Dust, clean it off with a blowerFilter cleaning Punch dust removal Cleaning the processor rack Cleaning the processor sectionResetting the punch counter Processor rack Stay Cleaning the processing chemical tank and filter Re-attach the supply guides to the processor rackCleaning the processing chemical supply pipe Cleaning the nip roller and exit roller Upper Cleaning the exit roller lower Set screw Roller fixing bracket Washing tank Bearing for a roller Exit roller lower Cleaning the washing tank Left tray rail Set screw Around when you remove the hose Slide the washing tank Replacing the diffusion sheet SLM-EAC, SLM-EST Put the accompanying diffusion How to order parts List of expendable partsMonth Year SDP-Eco 1630 III Maintenance and Inspection Chart Message Displaying and clearing errorsMessage Status display Message Operation statusList of error messages Message Error contentsME9 Jam removal procedure Removing Plate jam 1Removing Plate jam Specifications Basic specificationsOverview diagram Silver Digiplater