Mitsubishi Electronics SDP-ECO 1630 III manual ME9

Page 78

SDP-Eco1630 III USERS MANUAL

Message

Error contents

 

 

ME9

A problem occurred in the heat roller. Please contact the

 

dealer where you purchased this machine.

 

 

ME10

A problem occurred when the punch unit was activated.

 

Please contact the dealer where you purchased this

 

machine.

 

 

ME11

A problem occurred in the laser adjustment unit. Please

 

contact the dealer where you purchased this machine.

 

 

Punch Un-mounted

The punch is not mounted.

 

 

Close front door

The front door is open. Shut the door.

 

 

Width not enough

The width of the plate is insufficient for the exposure

 

width. Replace the plate with one as wide as the

 

exposure.

 

 

Image Error

An internal data transmission error occurred in the SDP-

 

Eco 1630 III. Re-boot the machine.

 

If this error occurs frequently, please contact the dealer

 

where you purchased this machine.

 

 

Plate Set error

The plate has not been set correctly. Re-set the plate.

 

 

Plate End

The plate ran out. Load a new plate.

 

 

Pick up plate

Open the front door and remove a strip type plate

 

through the plate removal port.

 

 

Waste Tank Check

The waste chemical tank is full.

 

 

Empty EAC

The EAC chemical ran out. Replenish it.

 

 

Empty EST

The EST chemical ran out. Replenish it.

 

 

Tray check

The overflow tray has not been set. Set the tray.

 

 

I/F error4

An error has occurred in the SCSI communication. If the

 

error frequently occurs even after the system has been

 

rebooted, contact your local dealer where you purchased

 

this machine.

 

 

Please set plate

A plate has not been set. Set the plate.

 

 

SRAM BOARD ERR #1

A problem occurred in the I/F board. Please contact the

 

dealer where you purchased this machine.

 

 

SRAM BOARD ERR #2

A problem occurred in the I/F board. Please contact the

 

dealer where you purchased this machine.

 

 

SRAM BOARD ERR #3

A problem occurred in the I/F board. Please contact the

 

dealer where you purchased this machine.

 

 

NO SUPPORT DIMM

A problem occurred in the memory module for buffer.

 

Please contact the dealer where you purchased this

 

machine.

 

 

MEM VERIFIY ERR

A problem occurred in the memory module for buffer.

 

Please contact the dealer where you purchased this

 

machine.

 

 

3.3V REG. ERR NN

A problem occurred in the I/F board. Please contact the

 

dealer where you purchased this machine.

 

 

- 70 -

Image 78
Contents Page III For Your Safety Compliance with FCC Rules When export the machineCompliance with Cispr Rules Limit of responsibilityIntroductory Note About this manual Contents Menus and panel displays Power supply On SafetyWhen using the machine Maintenance and safe passage during emergenciesSDP-Eco 1630 III is equipped with a leakage circuit breaker This machine incorporates a power supply unitSafety switches This machine incorporates high current electrical circuitsFor European model Types of warning labels Hazard Safe handling methodLocations of the machines warning labels are shown below Handling processing chemicals Processing chemical components Before connecting the power cable Power cablesOperation precautions UnacceptableTransport and installation Precautions during transport and installationSDP-Eco 1630 III Installation Installation environmentVentilation Maintenance Installation spaceMachine disposal Page Names of Machine Components and Parts Main unitPage Operation panel Safety switch Plate setting Handling platesTwo set screws are Refer to 4.1 Cable Insert the plate edge until Plate end processing Page Operation Cable connection checkTurning on the power switch InitializationPanel display flow after machine startup Press the Menu Key to display Amount using the key or Key and register the value with Exposure Remote exposureLocal exposure Exposure Processor section Preparing and pouring processing chemicalProcessing chemical replenishment Processing chemical replacement Preparing rinse waterHandling waste liquid If the machine is not used for a long periodTurning OFF the power supply and inspection at shutdown Collecting exposed platesOperation Page Menus and panel displays User menuOperation status Menu/command selection Power ON/OFF keyRemote mode display Panel operationSwitch the mode between remote and local Shift between commands ExampleCommand execution Data channel User menuPlate data Plate typeLaser menu Resolution settingLaser setting Remaining amount of plateLaser test exposure Pre. Feed menu Mode menuPunch specifications Image Data menuMaintenance menu RinseProcedure In cases where the current values are changed to KeyMaintenance Cutter blade replacementReplacement procedure Cylindrical lens cleaning Dust, clean it off with a blowerFilter cleaning Punch dust removal Cleaning the processor section Resetting the punch counterCleaning the processor rack Processor rack Stay Cleaning the processing chemical tank and filter Re-attach the supply guides to the processor rackCleaning the processing chemical supply pipe Cleaning the nip roller and exit roller Upper Cleaning the exit roller lower Set screw Roller fixing bracket Washing tank Bearing for a roller Exit roller lower Cleaning the washing tank Left tray rail Set screw Around when you remove the hose Slide the washing tank Replacing the diffusion sheet SLM-EAC, SLM-EST Put the accompanying diffusion How to order parts List of expendable partsMonth Year SDP-Eco 1630 III Maintenance and Inspection Chart Displaying and clearing errors MessageMessage Status display Message Operation statusList of error messages Message Error contentsME9 Jam removal procedure Removing Plate jam 1Removing Plate jam Specifications Basic specificationsOverview diagram Silver Digiplater