Mitsubishi Electronics SDP-ECO 1630 III Compliance with Cispr Rules, Compliance with FCC Rules

Page 4

Compliance with CISPR Rules

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Compliance with FCC Rules

Notice for the USA

This machine has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the machine is operated in a commercial environment. This machine generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this machine in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own expense.

Changes or modifications not expressly approved by Mitsubishi Paper Mills Limited could void the user's authority to operate the machine.

Notice for Canada

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Unit Regulations.

Cet appareil numérique de la Class A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

When export the machine

International transfer of this product, any of its parts, components and/or software must be carried out in compliance with the relevant laws and ordinance of the country of export and the country of product end-use. We do not assume any responsibility of liability for product transferred without regard to proper export/import regulations or procedures.

Limit of responsibility

Please note that machine specifications are subject to change without notice for updates and improvements. This may cause inconsistencies between the contents of this manual and the machine you currently possess.

We shall not be held responsible for any damage caused by conditions beyond our control such as customer modification, disassembly or misuse of our machine, programs or software, or their use in a defective or deficient environment.

We assume no responsibility or liability for any damage or consequential and/or indirect losses resulting from any accident or malfunction that might occur during the operation of this machine.

Copyright

©2005: Mitsubishi Paper Mills Limited.

The copyright for this entire manual belongs to Mitsubishi Paper Mills Limited.

Copying, reprinting, or reproduction of this manual in whole or in part in any medium without our express consent infringes upon the copyright and the rights of the publisher.

ii

Image 4
Contents Page III For Your Safety When export the machine Compliance with Cispr RulesCompliance with FCC Rules Limit of responsibilityIntroductory Note About this manual Contents Menus and panel displays On Safety When using the machinePower supply Maintenance and safe passage during emergenciesThis machine incorporates a power supply unit Safety switchesSDP-Eco 1630 III is equipped with a leakage circuit breaker This machine incorporates high current electrical circuitsFor European model Types of warning labels Hazard Safe handling methodLocations of the machines warning labels are shown below Handling processing chemicals Processing chemical components Before connecting the power cable Power cablesOperation precautions UnacceptablePrecautions during transport and installation SDP-Eco 1630 III InstallationTransport and installation Installation environmentVentilation Maintenance Installation spaceMachine disposal Page Names of Machine Components and Parts Main unitPage Operation panel Safety switch Plate setting Handling platesTwo set screws are Refer to 4.1 Cable Insert the plate edge until Plate end processing Page Operation Cable connection checkInitialization Turning on the power switchPanel display flow after machine startup Press the Menu Key to display Amount using the key or Key and register the value with Remote exposure ExposureLocal exposure Exposure Preparing and pouring processing chemical Processor sectionProcessing chemical replenishment Processing chemical replacement Preparing rinse waterHandling waste liquid If the machine is not used for a long periodTurning OFF the power supply and inspection at shutdown Collecting exposed platesOperation Page Menus and panel displays User menuOperation status Power ON/OFF key Remote mode displayMenu/command selection Panel operationShift between commands Example Switch the mode between remote and localCommand execution User menu Plate dataData channel Plate typeResolution setting Laser settingLaser menu Remaining amount of plateLaser test exposure Mode menu Punch specificationsPre. Feed menu Image Data menuMaintenance menu RinseProcedure In cases where the current values are changed to KeyCutter blade replacement MaintenanceReplacement procedure Cylindrical lens cleaning Dust, clean it off with a blowerFilter cleaning Punch dust removal Resetting the punch counter Cleaning the processor sectionCleaning the processor rack Processor rack Stay Cleaning the processing chemical tank and filter Re-attach the supply guides to the processor rackCleaning the processing chemical supply pipe Cleaning the nip roller and exit roller Upper Cleaning the exit roller lower Set screw Roller fixing bracket Washing tank Bearing for a roller Exit roller lower Cleaning the washing tank Left tray rail Set screw Around when you remove the hose Slide the washing tank Replacing the diffusion sheet SLM-EAC, SLM-EST Put the accompanying diffusion How to order parts List of expendable partsMonth Year SDP-Eco 1630 III Maintenance and Inspection Chart Message Displaying and clearing errorsMessage Status display Message Operation statusList of error messages Message Error contentsME9 Jam removal procedure Removing Plate jam 1Removing Plate jam Specifications Basic specificationsOverview diagram Silver Digiplater