JVC DLA-QX1G manual Remove the slot panel from the slot, Projector, Install the VIC

Page 15

Connector Panel (Cont.)

About the optional VICs

HDTV Analog VIC

ÅLED

This LED lights up when the HDTV Analog VIC is selected.

ıY, Pb, Pr input terminal (BNC x 3)

These are Y, Pb, Pr input terminals for HD signal (SMPTE260M/274M/296M).

HD-SDI VIC

ÅLED

This LED lights up when the HD-SDI VIC is se- lected.

ıSDI input/output (through) terminal (BNC x 2) These are input and output terminals for HD-SDI signal (SMPTE292M).

Å

HDTV Analog VIC

Y Pb Pr

ı

Åı

HD-SDI VIC

INOUT

How to install the optional VICs

1 Remove the slot panel from the slot of the			OUT	RS-232C
projector.		NTROL	REMOTE	R
			-232C
1) Remove two screws on the slot panel, one on each end,	CO		B Y
1) Remove two screws on the slot panel, one on each end,		VIC	B Y	H/C
			G	H/C
from an empty slot.		Analog
from an empty slot.	RGB

2) Take off the slot panel.

ENGLISH

2Install the VIC.

1)Aligning both ends of the PC board of the VIC with the grooves inside the slot, insert the VIC into the slot.

2)Push the VIC fully so that two connectors on inner surface of the VIC are securely plugged into the sockets inside the slot.

3Fasten the VIC to the projector.

After inserting the VIC into the slot, fasten it to the projector with two screws attached to the VIC.

				RS-232C
			C O	UT
			C O
			232
	REM	OTE
CONTROL	REM			R
			G	H/C
VIC		B	Y
Analog
RGB

P

	VIC	P
	Analog	Y
HD	TV	Y

				RS-232C
			OUT
			-232C
CONTROL	REMOTE			B
CONTROL
			G	H/C
	VIC	R	Y
Analog
RGB
			P
	VIC		P
Analog		Y
HDTV

Notes

•To avoid penetrating of the dust, do not remove the slot panel from the unused VIC slot.

• When replacing the slot panel, set it with the arrow up (indicated on the both ends of the slot panel) as shown:

arrow

13

Image 15

Contents Pour l’utilisateur For Customer UsePage DLA-QX1G About burning-in of the D-ILA device About the plug U.S.A. onlySafety Precautions Important SafeguardsDo not allow any unqualified person to install the unit Do not cut off the main plug from this equipment Information on the power cord plugContents Video Interface Card VIC AccessoriesInformation on separately sold items Projection lensFront Side / Top Surface / Right Side Controls and FeaturesLeft-hand side / Back Side To remove the handlesIntake area filter Control Panel About status code Connector Panel Fasten the VIC to the projector Install the VICRemove the slot panel from the slot ProjectorRemote Control Unit Shift +/- buttons Wired remote control terminalLock Ô Unlock switch Shutter ON/OFF buttonsCursor 5/∞/2/3 / Enter Menu Operation Button Installing BatteriesOpen the back cover Install the batteries Precautions for using batteriesAllowable minimum space required Installing the ProjectorPrecautions for Installation When installing the projector, observe the following305 mm Or more Adjusting the Inclination of the Projector Adjusting the vertical angle of the projectorLeveling the projector Projection using stack configuration Installing the Projector against the ScreenLens model Function Projection Distance and Screen SizeLens type Approximate projection distance Optional LensesFor the lenses with the lens shift function Lens Shift FunctionMaximum amount of shift Relational table for maximum shift amounts aspect ratio 4Effective Range and Distance of the Remote Control Unit Using as a wireless remote control unitUsing as a wired remote control unit Digital HD signals Connecting to Various DevicesSignals that Can Be Input to the Projector Analog HD signalsExample of a basic system Examples of System ConfigurationDesktop type Connecting to RGB DevicesAnalog HD devices Connecting to Analog HD DevicesConnecting to Digital HD Devices Digital HD devicesDigital HD monitor Connecting to Devices which Control the Projector Projector Connecting the Power Cord SuppliedInsert the supplied power cord Into the power input terminal ACBasic Operations Turning On the PowerTurn on the Main Power switch of the projector Remote control unitTo change the menu language displayed Code displaySelecting the VIC to be projected Adjusting Focus Adjusting the Screen SizeTurning off video image Hide For Operating Other FunctionsPress the Keystone / buttons Image KeystoneSetting the amount of lens shifting Shift Press the Shift + buttonPress the Shift button Menu Operations No signal menu modeMain menu Sub menu RGB VIC menu modeHdtv VIC or HD-SDI VIC menu mode To go to the sub menu To select or adjust the itemButtons and Control for Menu Operations To display the main menuMenu Operation Procedure Contents of the Menu VIC menu VIC menu 1/2 For RGB VICFor HDTV/HD-SDI VIC Sub brightness menu Options menuLanguage menu Color temp. menuMenu position menu Offset & Gain menuUser 1 or 2 menu Lens shift menuCleaning and Replacing the Filters Remove the filter coverRemove the filters Reinstall the filters Clean the filtersWhen the lamp’s use hours exceed 900 hours When lamp’s use hours has reached 1000 hoursReplacing the Light-Source Lamp Corrective action TroubleshootingTroubleshooting Message Cause Corrective action Error code Cause Corrective action Appendix GL-MQ1010GUnit ft m GL-MQ1015SG GL-MQ1020ZG GL-MQ1023SZG RGB in RGB input SpecificationsGeneral Pin assignment Specifications for terminals Outside dimensionsCommunication Specifications Command FormatRS-232C external control