JVC DLA-QX1G manual Installing the Projector, Precautions for Installation

Page 19

Installing the Projector

Precautions for Installation

CAUTIONS

Since the projector weighs approx. 92 kg (203 lbs.), be sure to have four or more people when lifting or moving it; otherwise, the projector could possibly drop, causing personal injury and/or damage to the projector.

Do not install the projector in the following places:

There is much water, humidity or dust.

The projector may be subjected to oil smoke or cigarette smoke.

On a soft surface such as a carpet or cushion.

The projector may be subjected to direct sunlight.

Temperature is high or humidity is low.

Allowable operation temperature range: + 5°C to + 35°C (41°F to 95°F)

Allowable relative humidity range:

20% to 80% (no condensation)

Allowable storage temperature range:

–10°C to +60°C (14°F to 140°F)

When installing the projector, observe the following:

Do not use the projector placed on its side or upside down.

The projector cannot be used by being placed on its side or upside down; otherwise, it could malfunction.

Use the projector within the range of allowable installation angle.

Avoid using the projector inclined over 5° right-to-left or left-to-right, over 25° front-to-rear or rear-to-front; otherwise it could cause color variation or harm the lamp life.

Do not block the exhaust vents.

Do not use a cover which encloses the projector intake or blocks the exhaust vents. Allow sufficient space around the projector. When the projector is enclosed in a space of the following dimensions, use an air conditioner so the temperature inside becomes equal to the outside temperature.

Allowable minimum space required

Front view

305 mm (12”)

ENGLISH

 

600 mm (23-5/8”)

 

600 mm (23-5/8”)

Right side view

305 mm (12”)

CONTROL

REMOTE

RS-232C OUT

RS-232C IN

RGB Analog VIC

RGB

Y H/C

600 mm (23-5/8”)

17

Image 19
Contents Pour l’utilisateur For Customer UsePage DLA-QX1G About burning-in of the D-ILA device About the plug U.S.A. onlySafety Precautions Important SafeguardsDo not allow any unqualified person to install the unit Do not cut off the main plug from this equipment Information on the power cord plugContents Video Interface Card VIC AccessoriesInformation on separately sold items Projection lensFront Side / Top Surface / Right Side Controls and FeaturesTo remove the handles Left-hand side / Back SideIntake area filter Control Panel About status code Connector Panel Fasten the VIC to the projector Install the VICRemove the slot panel from the slot ProjectorRemote Control Unit Shift +/- buttons Wired remote control terminalLock Ô Unlock switch Shutter ON/OFF buttonsCursor 5/∞/2/3 / Enter Menu Operation Button Installing BatteriesOpen the back cover Install the batteries Precautions for using batteriesAllowable minimum space required Installing the ProjectorPrecautions for Installation When installing the projector, observe the following305 mm Or more Adjusting the vertical angle of the projector Adjusting the Inclination of the ProjectorLeveling the projector Projection using stack configuration Installing the Projector against the ScreenLens model Function Projection Distance and Screen SizeLens type Approximate projection distance Optional LensesFor the lenses with the lens shift function Lens Shift FunctionMaximum amount of shift Relational table for maximum shift amounts aspect ratio 4Using as a wireless remote control unit Effective Range and Distance of the Remote Control UnitUsing as a wired remote control unit Digital HD signals Connecting to Various DevicesSignals that Can Be Input to the Projector Analog HD signalsExample of a basic system Examples of System ConfigurationDesktop type Connecting to RGB DevicesAnalog HD devices Connecting to Analog HD DevicesDigital HD devices Connecting to Digital HD DevicesDigital HD monitor Connecting to Devices which Control the Projector Projector Connecting the Power Cord SuppliedInsert the supplied power cord Into the power input terminal ACBasic Operations Turning On the PowerTurn on the Main Power switch of the projector Remote control unitTo change the menu language displayed Code displaySelecting the VIC to be projected Adjusting Focus Adjusting the Screen SizeTurning off video image Hide For Operating Other FunctionsPress the Keystone / buttons Image KeystonePress the Shift + button Setting the amount of lens shifting ShiftPress the Shift button Menu Operations No signal menu modeMain menu Sub menu RGB VIC menu modeHdtv VIC or HD-SDI VIC menu mode To go to the sub menu To select or adjust the itemButtons and Control for Menu Operations To display the main menuMenu Operation Procedure Contents of the Menu For RGB VIC VIC menu VIC menu 1/2For HDTV/HD-SDI VIC Sub brightness menu Options menuLanguage menu Color temp. menuMenu position menu Offset & Gain menuUser 1 or 2 menu Lens shift menuRemove the filter cover Cleaning and Replacing the FiltersRemove the filters Reinstall the filters Clean the filtersWhen lamp’s use hours has reached 1000 hours When the lamp’s use hours exceed 900 hoursReplacing the Light-Source Lamp Corrective action TroubleshootingTroubleshooting Message Cause Corrective action Error code Cause Corrective action GL-MQ1010G AppendixUnit ft m GL-MQ1015SG GL-MQ1020ZG GL-MQ1023SZG RGB in RGB input SpecificationsGeneral Pin assignment Specifications for terminals Outside dimensionsCommand Format Communication SpecificationsRS-232C external control