JVC DLA-QX1G manual Clean the filters, Reinstall the filters

Page 51

4 Clean the filters.

Wash the filter in water with neutral detergent, and dry it in the shade.

5 Reinstall the filters.

Reverse the procedure for removing. Finally, be sure to reinstall the filter covers.

Notes

•Install the filters correctly; otherwise the projector will not operate normally.

•If the filters and/or filter covers are damaged, the projector may fail to operate. Then, replace with new parts.

CAUTIONS

•Put on rubber gloves when using neutral detergent.

•After you have washed the filters in water, make sure the filters are completely dry before reinstalling them. Otherwise, electric shock or malfunction could occur.

•Do not clean the filters using a vacuum cleaner. Since the filters are soft, it may be sucked into the vacuum cleaner or damaged.

ENGLISH

49

Image 51

Contents Pour l’utilisateur For Customer UsePage DLA-QX1G About burning-in of the D-ILA device About the plug U.S.A. onlySafety Precautions Important SafeguardsDo not allow any unqualified person to install the unit Do not cut off the main plug from this equipment Information on the power cord plugContents Video Interface Card VIC AccessoriesInformation on separately sold items Projection lensFront Side / Top Surface / Right Side Controls and FeaturesLeft-hand side / Back Side To remove the handlesIntake area filter Control Panel About status code Connector Panel Fasten the VIC to the projector Install the VICRemove the slot panel from the slot ProjectorRemote Control Unit Shift +/- buttons Wired remote control terminalLock Ô Unlock switch Shutter ON/OFF buttonsCursor 5/∞/2/3 / Enter Menu Operation Button Installing BatteriesOpen the back cover Install the batteries Precautions for using batteriesAllowable minimum space required Installing the ProjectorPrecautions for Installation When installing the projector, observe the following305 mm Or more Adjusting the Inclination of the Projector Adjusting the vertical angle of the projectorLeveling the projector Projection using stack configuration Installing the Projector against the ScreenLens model Function Projection Distance and Screen SizeLens type Approximate projection distance Optional LensesFor the lenses with the lens shift function Lens Shift FunctionMaximum amount of shift Relational table for maximum shift amounts aspect ratio 4Effective Range and Distance of the Remote Control Unit Using as a wireless remote control unitUsing as a wired remote control unit Digital HD signals Connecting to Various DevicesSignals that Can Be Input to the Projector Analog HD signalsExample of a basic system Examples of System ConfigurationDesktop type Connecting to RGB DevicesAnalog HD devices Connecting to Analog HD DevicesConnecting to Digital HD Devices Digital HD devicesDigital HD monitor Connecting to Devices which Control the Projector Projector Connecting the Power Cord SuppliedInsert the supplied power cord Into the power input terminal ACBasic Operations Turning On the PowerTurn on the Main Power switch of the projector Remote control unitTo change the menu language displayed Code displaySelecting the VIC to be projected Adjusting Focus Adjusting the Screen SizeTurning off video image Hide For Operating Other FunctionsPress the Keystone / buttons Image KeystoneSetting the amount of lens shifting Shift Press the Shift + buttonPress the Shift button Menu Operations No signal menu modeMain menu Sub menu RGB VIC menu modeHdtv VIC or HD-SDI VIC menu mode To go to the sub menu To select or adjust the itemButtons and Control for Menu Operations To display the main menuMenu Operation Procedure Contents of the Menu VIC menu VIC menu 1/2 For RGB VICFor HDTV/HD-SDI VIC Sub brightness menu Options menuLanguage menu Color temp. menuMenu position menu Offset & Gain menuUser 1 or 2 menu Lens shift menuCleaning and Replacing the Filters Remove the filter coverRemove the filters Reinstall the filters Clean the filtersWhen the lamp’s use hours exceed 900 hours When lamp’s use hours has reached 1000 hoursReplacing the Light-Source Lamp Corrective action TroubleshootingTroubleshooting Message Cause Corrective action Error code Cause Corrective action Appendix GL-MQ1010GUnit ft m GL-MQ1015SG GL-MQ1020ZG GL-MQ1023SZG RGB in RGB input SpecificationsGeneral Pin assignment Specifications for terminals Outside dimensionsCommunication Specifications Command FormatRS-232C external control