JVC DLA-QX1G manual Menu Operations, No signal menu mode

Page 41

Menu Operations

You can adjust picture quality, set functions, get information on the input video signal, etc. using the menus. From the following diagrams, you can see the overall menus. Note that there are three menu modes: No signal menu mode, RGB VIC menu mode and HDTV/HD-SDI VIC menu mode. When the MENU button is pressed, the projector enters one of these modes by judging the input signal being received.

■No signal menu mode

The following diagram shows the menu transition when there is no signal input through the selected VIC.

Main menu				Sub menu 1
Menu				Options
Image adj.				Right Left rev.	OFF		ON
Setting	Right Left rev.			RS-232C [bps]	9600		19200
VIC menu	Right Left rev.			Sleep time [min]	15 30		60 OFF
Options	RS-232C[bps]			Options menu
Language	Sleep time [min]

Information

Main : Options

Menu

Image adj.

Setting English

VIC menu Deutsch

Options Español

Language Italiano

Information Français

Main : Language

Menu

	Image adj. VIC Slot 1		RGB
	Setting	Switcher	CH.0
	VIC menu
		Resolution 1024 x 768
	Options
		Frequency H 48.5kHz
	Language
		Frequency V	80 Hz

	Information Lamp time		123 h

Main : Information

Back to “Main : Options”

Language

English

Deutsch

Español

Italiano

Français

Language menu

Note

•The display languages of the menus are set to “English” when

shipped from the factory. The display language can be selected from

the following 6 languages: “ (Japanese),” “English,” “Deutsch (German),” “Español (Spanish),” “Italiano (Italian)” and “Français (French).” The language settings in this section are explained using English menus.

For details, refer to page 46.

ENGLISH

(To be continued on the next page)

39

Image 41

Contents Pour l’utilisateur For Customer UsePage DLA-QX1G About burning-in of the D-ILA device About the plug U.S.A. onlySafety Precautions Important SafeguardsDo not allow any unqualified person to install the unit Do not cut off the main plug from this equipment Information on the power cord plugContents Information on separately sold items AccessoriesProjection lens Video Interface Card VICFront Side / Top Surface / Right Side Controls and FeaturesIntake area filter Left-hand side / Back SideTo remove the handles Control Panel About status code Connector Panel Remove the slot panel from the slot Install the VICProjector Fasten the VIC to the projectorRemote Control Unit Lock Ô Unlock switch Wired remote control terminalShutter ON/OFF buttons Shift +/- buttonsOpen the back cover Install the batteries Installing BatteriesPrecautions for using batteries Cursor 5/∞/2/3 / Enter Menu Operation ButtonPrecautions for Installation Installing the ProjectorWhen installing the projector, observe the following Allowable minimum space required305 mm Or more Leveling the projector Adjusting the Inclination of the ProjectorAdjusting the vertical angle of the projector Projection using stack configuration Installing the Projector against the ScreenLens type Approximate projection distance Projection Distance and Screen SizeOptional Lenses Lens model FunctionFor the lenses with the lens shift function Lens Shift FunctionMaximum amount of shift Relational table for maximum shift amounts aspect ratio 4Using as a wired remote control unit Effective Range and Distance of the Remote Control UnitUsing as a wireless remote control unit Signals that Can Be Input to the Projector Connecting to Various DevicesAnalog HD signals Digital HD signalsExample of a basic system Examples of System ConfigurationDesktop type Connecting to RGB DevicesAnalog HD devices Connecting to Analog HD DevicesDigital HD monitor Connecting to Digital HD DevicesDigital HD devices Connecting to Devices which Control the Projector Insert the supplied power cord Connecting the Power Cord SuppliedInto the power input terminal AC ProjectorTurn on the Main Power switch of the projector Turning On the PowerRemote control unit Basic OperationsTo change the menu language displayed Code displaySelecting the VIC to be projected Adjusting Focus Adjusting the Screen SizeTurning off video image Hide For Operating Other FunctionsPress the Keystone / buttons Image KeystonePress the Shift button Setting the amount of lens shifting ShiftPress the Shift + button Menu Operations No signal menu modeMain menu Sub menu RGB VIC menu modeHdtv VIC or HD-SDI VIC menu mode Buttons and Control for Menu Operations To select or adjust the itemTo display the main menu To go to the sub menuMenu Operation Procedure Contents of the Menu For HDTV/HD-SDI VIC VIC menu VIC menu 1/2For RGB VIC Language menu Options menuColor temp. menu Sub brightness menuUser 1 or 2 menu Offset & Gain menuLens shift menu Menu position menuRemove the filters Cleaning and Replacing the FiltersRemove the filter cover Reinstall the filters Clean the filtersReplacing the Light-Source Lamp When the lamp’s use hours exceed 900 hoursWhen lamp’s use hours has reached 1000 hours Corrective action TroubleshootingTroubleshooting Message Cause Corrective action Error code Cause Corrective action Unit ft m AppendixGL-MQ1010G GL-MQ1015SG GL-MQ1020ZG GL-MQ1023SZG RGB in RGB input SpecificationsGeneral Pin assignment Specifications for terminals Outside dimensionsRS-232C external control Communication SpecificationsCommand Format