JVC DLA-QX1G manual Do not allow any unqualified person to install the unit

Page 6

SAFETY PRECAUTIONS (Cont.)

Slots and openings in the cabinet are provided for ventilation. These ensure reliable operation of the product and protect it from overheating. These openings must not be blocked or covered. (The openings should never be blocked by placing the product on bed, sofa, rug, or similar surface. It should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided and the manufacturer’s instructions have been adhered to.)

For proper ventilation, separate the product from other equipment, which may prevent ventilation and keep distance more than 60 cm (23-5/8”).

This product should be operated only with the type of power source indicated on the label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company.

This product is equipped with a three-wire plug. This plug will fit only into a grounded power outlet. If you are unable to insert the plug into the outlet, contact your electrician to install the proper outlet. Do not defeat the safety purpose of the grounded plug.

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them. Pay particular attention to cords at doors, plugs, receptacles, and the point where they exit from the product.

For added protection of this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the cable system. This will prevent damage to the product due to lightning and power line surges.

Do not overload wall outlets, extension cords, or convenience receptacles on other equipment as this can result in a risk of fire or electric shock.

Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltages and other hazards. Refer all service to qualified service personnel.

Do not look into the inside of this unit through vents (ventilation holes), etc. Do not look at the light-source lamp directly by opening the cabinet while the light-source lamp is turned on. The light-source lamp also contains ultraviolet rays and the light is so powerful that your eyesight can be impaired.

Xenon gas is enclosed with high pressure inside the light-source lamp (lamp unit) of this projector. If you drop or impart a shock to the lamp, or discard it as is, there is possibility of explosion, leading to personal injury. Use special care when handling the lamp. For any unclear points, consult your product dealer.

Use only the accessory cord designed for this product to prevent shock.

The power supply voltage rating of this product is AC 200 V to 240 V, the power cord attached conforms to the following power supply voltage. Use only the power cord designated by our dealer to ensure Safety and EMC.

When it is used by other power supply voltage, power cable must be changed. Consult your product dealer.

*DO NOT allow any unqualified person to install the unit.

Be sure to ask your dealer to install the unit (eg. attaching it to the ceiling) since special technical knowledge and skills are required for installation.

If installation is performed by an unqualified person, it may cause personal injury or electrical shock.

4

Image 6
Contents For Customer Use Pour l’utilisateurPage DLA-QX1G About the plug U.S.A. only About burning-in of the D-ILA deviceImportant Safeguards Safety PrecautionsDo not allow any unqualified person to install the unit Information on the power cord plug Do not cut off the main plug from this equipmentContents Projection lens AccessoriesInformation on separately sold items Video Interface Card VICControls and Features Front Side / Top Surface / Right SideLeft-hand side / Back Side To remove the handlesIntake area filter Control Panel About status code Connector Panel Projector Install the VICRemove the slot panel from the slot Fasten the VIC to the projectorRemote Control Unit Shutter ON/OFF buttons Wired remote control terminalLock Ô Unlock switch Shift +/- buttonsPrecautions for using batteries Installing BatteriesOpen the back cover Install the batteries Cursor 5/∞/2/3 / Enter Menu Operation ButtonWhen installing the projector, observe the following Installing the ProjectorPrecautions for Installation Allowable minimum space required305 mm Or more Adjusting the Inclination of the Projector Adjusting the vertical angle of the projectorLeveling the projector Installing the Projector against the Screen Projection using stack configurationOptional Lenses Projection Distance and Screen SizeLens type Approximate projection distance Lens model FunctionLens Shift Function For the lenses with the lens shift functionRelational table for maximum shift amounts aspect ratio 4 Maximum amount of shiftEffective Range and Distance of the Remote Control Unit Using as a wireless remote control unitUsing as a wired remote control unit Analog HD signals Connecting to Various DevicesSignals that Can Be Input to the Projector Digital HD signalsExamples of System Configuration Example of a basic systemConnecting to RGB Devices Desktop typeConnecting to Analog HD Devices Analog HD devicesConnecting to Digital HD Devices Digital HD devicesDigital HD monitor Connecting to Devices which Control the Projector Into the power input terminal AC Connecting the Power Cord SuppliedInsert the supplied power cord ProjectorRemote control unit Turning On the PowerTurn on the Main Power switch of the projector Basic OperationsCode display To change the menu language displayedSelecting the VIC to be projected Adjusting the Screen Size Adjusting FocusFor Operating Other Functions Turning off video image HideImage Keystone Press the Keystone / buttonsSetting the amount of lens shifting Shift Press the Shift + buttonPress the Shift button No signal menu mode Menu OperationsRGB VIC menu mode Main menu Sub menuHdtv VIC or HD-SDI VIC menu mode To display the main menu To select or adjust the itemButtons and Control for Menu Operations To go to the sub menuMenu Operation Procedure Contents of the Menu VIC menu VIC menu 1/2 For RGB VICFor HDTV/HD-SDI VIC Color temp. menu Options menuLanguage menu Sub brightness menuLens shift menu Offset & Gain menuUser 1 or 2 menu Menu position menuCleaning and Replacing the Filters Remove the filter coverRemove the filters Clean the filters Reinstall the filtersWhen the lamp’s use hours exceed 900 hours When lamp’s use hours has reached 1000 hoursReplacing the Light-Source Lamp Troubleshooting Corrective actionTroubleshooting Message Cause Corrective action Error code Cause Corrective action Appendix GL-MQ1010GUnit ft m GL-MQ1015SG GL-MQ1020ZG GL-MQ1023SZG Specifications RGB in RGB inputGeneral Outside dimensions Pin assignment Specifications for terminalsCommunication Specifications Command FormatRS-232C external control