JVC DLA-QX1G manual Projection Distance and Screen Size, Lens type Approximate projection distance

Page 23

Installing the Projector (Cont.)

Projection Distance and Screen Size

The range of projection distances that can be focused depends on the lens unit (not supplied) to be used. When the aspect ratio of the screen is 4:3, the range is as follows and you need to install the projector within this range.

Lens type

Approximate projection distance

GL-MQ1010G

3.9 ft (1.2 m) to 25.9 ft

(7.9 m)

GL-MQ1015SG

5.6 ft (1.7 m) to 40.3 ft

(12.3 m)

GL-MQ1020ZG

26.2 ft (8.0 m) to 280.3 ft (85.5 m)

GL-MQ1023SZG

28.2 ft (8.6 m) to 276.1 ft (84.2 m)

The value for projection distance is a guide (reference). The projected image size may vary depending on the manufactur- ing tolerance of the projection lens.

Change of projection screen according to aspect ratio

Screen with 4 : 3 aspect ratio

Screen with 16 : 9 aspect ratio

For detailed relation between projection distances and projection screen sizes, refer to Appendix. The relation for both 4:3 and 16:9 are listed there.

When adjusting the screen size, use a 4:3 aspect-ration picture. (A 16:9 aspect-ration picture is projected, based on the width of a 4:3 aspect-ratio picture.)

The diagonal length of a 16:9 aspect-ratio screen is about 91.8% that of a 4:3 aspect-ratio screen. This value is only a guide (reference).

If the keystone is adjusted, the projected screen becomes smaller.

Optional Lenses

This projector does not include a lens. You can select one of the optional lenses to adjust the projection distance. Please ask your dealer to buy and install the lens.

Lens model

Function

 

 

GL-MQ1010G

Powered focus for rear projection, short focal length lens (subject ratio 1:1), 0% influence.

 

 

GL-MQ1015SG

Powered focus, short focal length lens (subject ratio 1.5:1), manual vertical shift function pro-

 

vided, 0% to ±50% influence.

 

 

GL-MQ1020ZG

Powered zoom/powered focus, long focal length lens (subject ratio 2.1:1 to 4.9:1), 0% influence.

 

 

GL-MQ1023SZG

Powered zoom/powered focus, long focal length lens (subject ratio 3:1 to 7:1), manual vertical

 

shift function provided, 0% to ±50% influence.

 

 

ENGLISH

21

Image 23
Contents Pour l’utilisateur For Customer UsePage DLA-QX1G About burning-in of the D-ILA device About the plug U.S.A. onlySafety Precautions Important SafeguardsDo not allow any unqualified person to install the unit Do not cut off the main plug from this equipment Information on the power cord plugContents Video Interface Card VIC AccessoriesInformation on separately sold items Projection lensFront Side / Top Surface / Right Side Controls and FeaturesIntake area filter Left-hand side / Back SideTo remove the handles Control Panel About status code Connector Panel Fasten the VIC to the projector Install the VICRemove the slot panel from the slot ProjectorRemote Control Unit Shift +/- buttons Wired remote control terminalLock Ô Unlock switch Shutter ON/OFF buttonsCursor 5/∞/2/3 / Enter Menu Operation Button Installing BatteriesOpen the back cover Install the batteries Precautions for using batteriesAllowable minimum space required Installing the ProjectorPrecautions for Installation When installing the projector, observe the following305 mm Or more Leveling the projector Adjusting the Inclination of the ProjectorAdjusting the vertical angle of the projector Projection using stack configuration Installing the Projector against the ScreenLens model Function Projection Distance and Screen SizeLens type Approximate projection distance Optional LensesFor the lenses with the lens shift function Lens Shift FunctionMaximum amount of shift Relational table for maximum shift amounts aspect ratio 4Using as a wired remote control unit Effective Range and Distance of the Remote Control UnitUsing as a wireless remote control unit Digital HD signals Connecting to Various DevicesSignals that Can Be Input to the Projector Analog HD signalsExample of a basic system Examples of System ConfigurationDesktop type Connecting to RGB DevicesAnalog HD devices Connecting to Analog HD DevicesDigital HD monitor Connecting to Digital HD DevicesDigital HD devices Connecting to Devices which Control the Projector Projector Connecting the Power Cord SuppliedInsert the supplied power cord Into the power input terminal ACBasic Operations Turning On the PowerTurn on the Main Power switch of the projector Remote control unitTo change the menu language displayed Code displaySelecting the VIC to be projected Adjusting Focus Adjusting the Screen SizeTurning off video image Hide For Operating Other FunctionsPress the Keystone / buttons Image KeystonePress the Shift button Setting the amount of lens shifting ShiftPress the Shift + button Menu Operations No signal menu modeMain menu Sub menu RGB VIC menu modeHdtv VIC or HD-SDI VIC menu mode To go to the sub menu To select or adjust the itemButtons and Control for Menu Operations To display the main menuMenu Operation Procedure Contents of the Menu For HDTV/HD-SDI VIC VIC menu VIC menu 1/2For RGB VIC Sub brightness menu Options menuLanguage menu Color temp. menuMenu position menu Offset & Gain menuUser 1 or 2 menu Lens shift menuRemove the filters Cleaning and Replacing the FiltersRemove the filter cover Reinstall the filters Clean the filtersReplacing the Light-Source Lamp When the lamp’s use hours exceed 900 hoursWhen lamp’s use hours has reached 1000 hours Corrective action TroubleshootingTroubleshooting Message Cause Corrective action Error code Cause Corrective action Unit ft m AppendixGL-MQ1010G GL-MQ1015SG GL-MQ1020ZG GL-MQ1023SZG RGB in RGB input SpecificationsGeneral Pin assignment Specifications for terminals Outside dimensionsRS-232C external control Communication SpecificationsCommand Format