JVC DLA-QX1G manual Connector Panel

Page 14

Controls and Features (cont.)

Connector Panel

1

2

3

CONTROL

 

 

REMOTE

RS-232C OUT

RS-232C IN

RGB Analog VIC

 

 

4

 

 

B

G

R

5

V

H/CS

6

1REMOTE terminal (mini jack)

This terminal is used to directly connect the remote con- trol unit to the projector. Use the remote control cable sup- plied.

2RS-232C OUT terminal (D-sub 9 pin)

This is an RS-232C interface-specified terminal. When another DLA-QX1G is connected to this projector using this terminal, you can enable a computer to control plural DLA-QX1Gs at the same time.

For details, consult your dealer.

3RS-232C IN terminal (D-sub 9 pin)

This is a RS-232C interface-specified terminal. This projector can be controlled by a computer connected externally.

For details, consult your dealer.

4LED

This LED lights up when the RGB Analog VIC is selected.

5RGB IN terminals (BNC x 5)

These are multipurpose video input terminals that allow input of the following signals.

Analog RGB signals, vertical sync (V) signals, and horizontal sync (H) signals / composite signals (Cs). (Devices which have analog RGB signal output terminals can be connected.)

*Input of external sync signals is automatically detected. Detection of H/V signals or Cs signals causes automatic switching to external sync. The priority order is H/V > Cs.

The uppermost edge of the image may appear to bow if the sync signal input is composite sync (Cs) or G on sync signal. In this case, use separate sync signals for vertical sync (V) and horizontal sync (H).

6VIC slots (x 2)

You can install the optional VICs in this projector using these slots. The following VICs are available.

HDTV Analog VIC

This VIC enables the projector to be input the conventional HDTV signal (Y, Pb, and Pr).

HD-SDI VIC

This VIC enables the projector to be input and output the HD-SDI signal. The output terminal can be used as a line through terminal for checking the input signal by connecting the HD-SDI monitor or for using plural projectors at the same time.

For details, refer to page 13.

12

Image 14
Contents For Customer Use Pour l’utilisateurPage DLA-QX1G About the plug U.S.A. only About burning-in of the D-ILA deviceImportant Safeguards Safety PrecautionsDo not allow any unqualified person to install the unit Information on the power cord plug Do not cut off the main plug from this equipmentContents Projection lens AccessoriesInformation on separately sold items Video Interface Card VICControls and Features Front Side / Top Surface / Right SideIntake area filter Left-hand side / Back SideTo remove the handles Control Panel About status code Connector Panel Projector Install the VICRemove the slot panel from the slot Fasten the VIC to the projectorRemote Control Unit Shutter ON/OFF buttons Wired remote control terminalLock Ô Unlock switch Shift +/- buttonsPrecautions for using batteries Installing BatteriesOpen the back cover Install the batteries Cursor 5/∞/2/3 / Enter Menu Operation ButtonWhen installing the projector, observe the following Installing the ProjectorPrecautions for Installation Allowable minimum space required305 mm Or more Leveling the projector Adjusting the Inclination of the ProjectorAdjusting the vertical angle of the projector Installing the Projector against the Screen Projection using stack configurationOptional Lenses Projection Distance and Screen SizeLens type Approximate projection distance Lens model FunctionLens Shift Function For the lenses with the lens shift functionRelational table for maximum shift amounts aspect ratio 4 Maximum amount of shiftUsing as a wired remote control unit Effective Range and Distance of the Remote Control UnitUsing as a wireless remote control unit Analog HD signals Connecting to Various DevicesSignals that Can Be Input to the Projector Digital HD signalsExamples of System Configuration Example of a basic systemConnecting to RGB Devices Desktop typeConnecting to Analog HD Devices Analog HD devicesDigital HD monitor Connecting to Digital HD DevicesDigital HD devices Connecting to Devices which Control the Projector Into the power input terminal AC Connecting the Power Cord SuppliedInsert the supplied power cord ProjectorRemote control unit Turning On the PowerTurn on the Main Power switch of the projector Basic OperationsCode display To change the menu language displayedSelecting the VIC to be projected Adjusting the Screen Size Adjusting FocusFor Operating Other Functions Turning off video image HideImage Keystone Press the Keystone / buttonsPress the Shift button Setting the amount of lens shifting ShiftPress the Shift + button No signal menu mode Menu OperationsRGB VIC menu mode Main menu Sub menuHdtv VIC or HD-SDI VIC menu mode To display the main menu To select or adjust the itemButtons and Control for Menu Operations To go to the sub menuMenu Operation Procedure Contents of the Menu For HDTV/HD-SDI VIC VIC menu VIC menu 1/2For RGB VIC Color temp. menu Options menuLanguage menu Sub brightness menuLens shift menu Offset & Gain menuUser 1 or 2 menu Menu position menuRemove the filters Cleaning and Replacing the FiltersRemove the filter cover Clean the filters Reinstall the filtersReplacing the Light-Source Lamp When the lamp’s use hours exceed 900 hoursWhen lamp’s use hours has reached 1000 hours Troubleshooting Corrective actionTroubleshooting Message Cause Corrective action Error code Cause Corrective action Unit ft m AppendixGL-MQ1010G GL-MQ1015SG GL-MQ1020ZG GL-MQ1023SZG Specifications RGB in RGB inputGeneral Outside dimensions Pin assignment Specifications for terminalsRS-232C external control Communication SpecificationsCommand Format