JVC DLA-QX1G manual Adjusting the Inclination of the Projector, Leveling the projector

Page 21

Installing the Projector (Cont.)

Adjusting the Inclination of the Projector

The vertical angle and the leveling of the projector can be adjusted with the adjustable feet on the bottom of the projector.

■Adjusting the vertical angle of the projector

Lift the projector, rotate the front adjustable feet, and adjust the vertical angle within the range of 0° to 3.5°.

	+3.5
Extend	Shorten

■Leveling the projector

Lift the projector, rotate the adjustable feet, and adjust the horizontal angle until the projector is level.

+4.5˚	ENGLISH
–4.5˚

Extend	Shorten

19

Image 21

Contents Pour l’utilisateur For Customer UsePage DLA-QX1G About burning-in of the D-ILA device About the plug U.S.A. onlySafety Precautions Important SafeguardsDo not allow any unqualified person to install the unit Do not cut off the main plug from this equipment Information on the power cord plugContents Information on separately sold items AccessoriesProjection lens Video Interface Card VICFront Side / Top Surface / Right Side Controls and FeaturesLeft-hand side / Back Side To remove the handlesIntake area filter Control Panel About status code Connector Panel Remove the slot panel from the slot Install the VICProjector Fasten the VIC to the projectorRemote Control Unit Lock Ô Unlock switch Wired remote control terminalShutter ON/OFF buttons Shift +/- buttonsOpen the back cover Install the batteries Installing BatteriesPrecautions for using batteries Cursor 5/∞/2/3 / Enter Menu Operation ButtonPrecautions for Installation Installing the ProjectorWhen installing the projector, observe the following Allowable minimum space required305 mm Or more Adjusting the Inclination of the Projector Adjusting the vertical angle of the projectorLeveling the projector Projection using stack configuration Installing the Projector against the ScreenLens type Approximate projection distance Projection Distance and Screen SizeOptional Lenses Lens model FunctionFor the lenses with the lens shift function Lens Shift FunctionMaximum amount of shift Relational table for maximum shift amounts aspect ratio 4Effective Range and Distance of the Remote Control Unit Using as a wireless remote control unitUsing as a wired remote control unit Signals that Can Be Input to the Projector Connecting to Various DevicesAnalog HD signals Digital HD signalsExample of a basic system Examples of System ConfigurationDesktop type Connecting to RGB DevicesAnalog HD devices Connecting to Analog HD DevicesConnecting to Digital HD Devices Digital HD devicesDigital HD monitor Connecting to Devices which Control the Projector Insert the supplied power cord Connecting the Power Cord SuppliedInto the power input terminal AC ProjectorTurn on the Main Power switch of the projector Turning On the PowerRemote control unit Basic OperationsTo change the menu language displayed Code displaySelecting the VIC to be projected Adjusting Focus Adjusting the Screen SizeTurning off video image Hide For Operating Other FunctionsPress the Keystone / buttons Image KeystoneSetting the amount of lens shifting Shift Press the Shift + buttonPress the Shift button Menu Operations No signal menu modeMain menu Sub menu RGB VIC menu modeHdtv VIC or HD-SDI VIC menu mode Buttons and Control for Menu Operations To select or adjust the itemTo display the main menu To go to the sub menuMenu Operation Procedure Contents of the Menu VIC menu VIC menu 1/2 For RGB VICFor HDTV/HD-SDI VIC Language menu Options menuColor temp. menu Sub brightness menuUser 1 or 2 menu Offset & Gain menuLens shift menu Menu position menuCleaning and Replacing the Filters Remove the filter coverRemove the filters Reinstall the filters Clean the filtersWhen the lamp’s use hours exceed 900 hours When lamp’s use hours has reached 1000 hoursReplacing the Light-Source Lamp Corrective action TroubleshootingTroubleshooting Message Cause Corrective action Error code Cause Corrective action Appendix GL-MQ1010GUnit ft m GL-MQ1015SG GL-MQ1020ZG GL-MQ1023SZG RGB in RGB input SpecificationsGeneral Pin assignment Specifications for terminals Outside dimensionsCommunication Specifications Command FormatRS-232C external control