Texas Instruments SPRU938B manual Transmit Address Map Register XAM, Txadrmap

Page 32

www.ti.com

VLYNQ Port Registers

3.8Transmit Address Map Register (XAM)

The transmit address map register (XAM) is used to translate transmit packet addresses to remote device configuration bus addresses. The XAM is shown in Figure 16 and described in Table 13.

Figure 16. Transmit Address Map Register (XAM)

31

2

1

0

TXADRMAP

 

Reserved

R/W-0

 

 

R-0

LEGEND: R/W = Read/Write; R = Read only; -n= value after reset

 

 

 

Table 13. Address Map Register (XAM) Field Descriptions

Bit

Field

Value

Description

31-2

TXADRMAP

0-3FFF FFFFh

This field is subtracted from the slave configuration bus address [25:0] to obtain the zero

 

 

 

relative transmit packet address. This field should be programmed with a value of 0 (reset

 

 

 

value).

1-0

Reserved

0

Reserved. Always read as 0. Writes have no effect.

32

VLYNQ Port

SPRU938B –September 2007

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Users Guide Submit Documentation Feedback Contents Appendix B Appendix CList of Figures List of Tables Read This First Features Purpose of the PeripheralFunctional Block Diagram Industry Standards Compliance StatementExternal Clock Block Diagram Clock ControlSignal Descriptions Vlynq Signal DescriptionsPin Multiplexing Protocol DescriptionVlynq Functional Description Vlynq Module StructureWrite Operations Read Operations Initialization Auto-NegotiationAddress Translation Address Translation Example Single Mapped Region Register DM643x Vlynq ModuleDM643x Vlynq Module Remote Vlynq ModuleFlow Control Example 1. Address Translation ExampleReset Considerations Software Reset ConsiderationsHardware Reset Considerations Interrupt SupportInterrupt Generation Mechanism Block Diagram Writes to Interrupt Pending/Set RegisterRemote Interrupts Serial Bus Error InterruptsEdma Event Support Emulation Considerations Power ManagementEndianness Considerations Vlynq Register Address Space Vlynq Port Controller RegistersBlock Name Start Address End Address Size Acronym Register DescriptionRevision Register Revid Revision Register Revid Field DescriptionsRevmaj Revmin Bit Field Value DescriptionControl Register Ctrl Control Register Ctrl Field DescriptionsAoptdisable Bit FieldStatus Register Stat Status Register Stat Field DescriptionsNo error LerrorInterrupt Priority Vector Status/Clear Register Intpri Interrupt Status/Clear Register IntstatclrNointpend InstatInterrupt Pending/Set Register Intpendset Interrupt Pointer Register IntptrInterrupt Pointer Register Intptr Field Descriptions IntsetTxadrmap Transmit Address Map Register XAMAddress Map Register XAM Field Descriptions Receive Address Map Size 1 Register RAMS1 Receive Address Map Offset 1 Register RAMO1RXADRSIZE1 RXADROFFSET1Receive Address Map Size 2 Register RAMS2 Receive Address Map Offset 2 Register RAMO2RXADRSIZE2 RXADROFFSET2Receive Address Map Size 3 Register RAMS3 Receive Address Map Offset 3 Register RAMO3RXADRSIZE3 RXADROFFSET3Receive Address Map Size 4 Register RAMS4 Receive Address Map Offset 4 Register RAMO4RXADRSIZE4 RXADROFFSET4Chip Version Register Chipver Auto Negotiation Register AutngoChip Version Register Chipver Field Descriptions Auto Negotiation Register Autngo Field DescriptionsVlynq Port Remote Controller Registers Introduction Special 8b/10b Code GroupsSupported Ordered Sets Table A-1. Special 8b/10b Code GroupsFigure A-1. Packet Format 10-bit Symbol Representation Vlynq 2.0 Packet FormatField Value Description Vlynq 2.X Packets Vlynq 2.X Packets Write Performance Burst Size Interface Running at 76.5 MHZ Bit Words Mbits/sec Mbytes/secRead Performance Table B-3. Relative Performance with Various LatenciesThroughput Latency μsecTable C-1. Document Revision History Reference Additions/Modifications/DeletionsRfid Products ApplicationsDSP
Top Page Image Contents