Texas Instruments SPRU938B manual Vlynq 2.X Packets

Page 43

www.ti.com

VLYNQ 2.X Packets

A command, length, address, and start receive data from the idle stream. A flow enable was received for the command channel, but there is data to return, so the flow is followed by a channel 1 descriptor (the command for return data actually indicates a channel 1), and the channel 1 packet is now under way. A flow is now received for channel 1, but it is soon disabled so the channel 1 packet continues. The flow is enabled for channel one again, quickly after flow is released for channel 0, so the data continues for channel 0 when a flow is received again for channel 0. Channel 0 then receives a flow disable, completes its packet, followed by channel 1 flow disable, where the channel 1 packet is also completed.

SPRU938B –September 2007

VLYNQ Protocol Specifications

Submit Documentation Feedback

Image 43

Contents Users Guide Submit Documentation Feedback Contents Appendix C Appendix BList of Figures List of Tables Read This First Purpose of the Peripheral FeaturesIndustry Standards Compliance Statement Functional Block DiagramClock Control External Clock Block DiagramProtocol Description Signal DescriptionsVlynq Signal Descriptions Pin MultiplexingVlynq Module Structure Vlynq Functional DescriptionWrite Operations Read Operations Auto-Negotiation InitializationAddress Translation Register DM643x Vlynq Module Address Translation Example Single Mapped RegionRemote Vlynq Module DM643x Vlynq ModuleExample 1. Address Translation Example Flow ControlInterrupt Support Reset ConsiderationsSoftware Reset Considerations Hardware Reset ConsiderationsWrites to Interrupt Pending/Set Register Interrupt Generation Mechanism Block DiagramEdma Event Support Serial Bus Error InterruptsRemote Interrupts Endianness Considerations Power ManagementEmulation Considerations Acronym Register Description Vlynq Register Address SpaceVlynq Port Controller Registers Block Name Start Address End Address SizeBit Field Value Description Revision Register RevidRevision Register Revid Field Descriptions Revmaj RevminControl Register Ctrl Field Descriptions Control Register CtrlBit Field AoptdisableStatus Register Stat Field Descriptions Status Register StatLerror No errorInstat Interrupt Priority Vector Status/Clear Register IntpriInterrupt Status/Clear Register Intstatclr NointpendIntset Interrupt Pending/Set Register IntpendsetInterrupt Pointer Register Intptr Interrupt Pointer Register Intptr Field DescriptionsAddress Map Register XAM Field Descriptions Transmit Address Map Register XAMTxadrmap RXADROFFSET1 Receive Address Map Size 1 Register RAMS1Receive Address Map Offset 1 Register RAMO1 RXADRSIZE1RXADROFFSET2 Receive Address Map Size 2 Register RAMS2Receive Address Map Offset 2 Register RAMO2 RXADRSIZE2RXADROFFSET3 Receive Address Map Size 3 Register RAMS3Receive Address Map Offset 3 Register RAMO3 RXADRSIZE3RXADROFFSET4 Receive Address Map Size 4 Register RAMS4Receive Address Map Offset 4 Register RAMO4 RXADRSIZE4Auto Negotiation Register Autngo Field Descriptions Chip Version Register ChipverAuto Negotiation Register Autngo Chip Version Register Chipver Field DescriptionsVlynq Port Remote Controller Registers Table A-1. Special 8b/10b Code Groups IntroductionSpecial 8b/10b Code Groups Supported Ordered SetsVlynq 2.0 Packet Format Figure A-1. Packet Format 10-bit Symbol RepresentationField Value Description Vlynq 2.X Packets Vlynq 2.X Packets Write Performance Bit Words Mbits/sec Mbytes/sec Burst Size Interface Running at 76.5 MHZLatency μsec Read PerformanceTable B-3. Relative Performance with Various Latencies ThroughputReference Additions/Modifications/Deletions Table C-1. Document Revision HistoryDSP Products ApplicationsRfid