Analog Devices ADSP-TS201S specifications Ball Bgaed PIN Configurations

Page 41

ADSP-TS201S

576-BALL BGA_ED PIN CONFIGURATIONS

Figure 46 shows a summary of pin configurations for the

576-ball BGA_ED package and Table 35 lists the signal-to-ball assignments.

2	4		6	8	10	12	14	16	18	20	22	24
1	3	5	7	9	11		13	15	17	19	21	23

TOP VIEW

KEY:

SIGNAL

VDD

VDD_IO

VDD_DRAM

VDD_A

VREF

VSS

NO CONNECT

Figure 46. 576-Ball BGA_ED Pin Configurations1 (Top View, Summary)

1For a more detailed pin summary diagram, see the EE-179:ADSP-TS201S System Design Guidelines on the Analog Devices website (www.analog.com).

Rev. C Page 41 of 48 December 2006

Image 41

Contents ADSP-TS201S ADSP-TS201S Clock General-Purpose Algorithm Benchmarks at 600 MHzBenchmark Speed Cycles FIR filter per real tap 83 nsDual Integer ALU Ialu Dual Compute BlocksData Alignment Buffer DAB DSP Memory Program SequencerInterrupt Controller Flexible Instruction SetInternal Space External Port OFF-CHIP MEMORY/PERIPHERALS InterfaceHost Interface DMA ControllerMultiprocessor Interface Sdram ControllerDMA controller provides these additional features Reset and Booting Timer and GENERAL-PURPOSE I/ONo Boot, Run from Memory Addresses Link Ports LvdsDevelopment Tools Power DomainsFiltering Reference Voltage and Clocks Additional Information Evaluation KITSignal Type Term Description Pin Definitions-Clocks and ResetSclk Ratio RatioACK T/OD Pin Definitions-External Port Bus ControlsPin Definitions-External Port Arbitration Signal TypeDSP performs DMA transfers according to the DMA Pin Definitions-External Port DMA/FlybySample the data instead of the TigerSHARC MakesLdqm Pin Definitions-External Port Sdram ControllerHdqm SDA10Pin Definitions-JTAG Port Signal Type Term Description Pin Definitions-Flags, Interrupts, and TimerCONTROLIMP0 Pin Definitions-Link PortsCONTROLIMP1 DS1Driver Mode Pin Definitions-Power, Ground, and ReferenceDS2-0 Drive Output Pins Strength Impedance Impedance Control SelectionPin Rstin = Pin Definitions-I/O Strap PinsType at Signal Reset Sclkvref Operating ConditionsMaximum Duty Cycle for Input Transient Voltage Electrical CharacteristicsMaximum Duty VIN Max VIN Min Cycle2ESD Sensitivity Package InformationAbsolute Maximum Ratings Package Brand InformationAC Asynchronous Signal Specifications Timing SpecificationsGeneral AC Timing Reference Clocks-Core Clock Cclk Cycle TimeReference Clocks-JTAG Test Clock TCK Cycle Time Reference Clocks-System Clock Sclk Cycle TimeSclkrat = 5⋅, 7⋅ Parameter Description Min Max Unit Parameter Description Min Max UnitPower-Up Reset Timing Power-Up Timing1On-Chip Dram Refresh1 Normal Reset TimingOutputDisable Max AC Signal SpecificationsStrap Pins DS2-0 Static Pins-Must Be ConstantJtag SYS 11 Jtag System Pins +2.5 +10.0 +12.0 Strap SYS 9Link Port Lvds Receive Electrical Characteristics Link Port Lvds Transmit Electrical CharacteristicsParameter Description Test Conditions Min Max Unit VODParameter Description Min Max Unit Link Port-Data Out TimingLink Ports-Output Clock Link Ports-Transmission End and Stops LxBCMPI Hold Figure Link Port-Data In TimingLink Ports-Data Input Setup and Hold1 Typical Drive Currents at Strength Output Drive CurrentsTest Conditions Output Disable TimeCapacitive Loading Output Enable TimeTimes Andfall Rise Fall Time Thermal Characteristics for 25 mm × 25 mm Package Thermal CharacteristicsEnvironmental Conditions Parameter Condition Typical UnitBall Bgaed PIN Configurations Ball 25 mm × 25 mm Bgaed Ball Assignments Ball No Signal NameL0ACKO Sdcke SCLKRAT1L0DATI1N L0DATI3NID2 TDI TMR0E DS2 Enedreg TCKDS1 CONTROLIMP1 TDO FLAG3 L1CLKINNBGA Data for Use with Surface Mount Design Surface Mount DesignPackage Ball Attach Type Solder Mask Opening Ball Pad Size Ball Bgaed Nonsolder Mask Defined Nsmd Mm diameter BP-576Operating Voltage Option Description Temperature Instruction On-Chip Package Model Range1 Rate2Ordering Guide Rev. C Page 47 of 48 December Rev. C Page 48 of 48 December