Analog Devices ADSP-TS201S specifications BGA Data for Use with Surface Mount Design

Page 45

ADSP-TS201S

OUTLINE DIMENSIONS

The ADSP-TS201S processor is available in a 25 mm × 25 mm, 576-ball metric thermally enhanced ball grid array (BGA_ED) package with 24 rows of balls (BP-576).

1.25

1.00

0.75

25.20

25.00

24.80

A1 BALL

INDICATOR


24	22		20		18		16		14		12		10	8	6	4		2
23		21		19		17		15		13		11		9	7	5	3	1

1.00 BSC

23.00

A

B

C

D

E

F

G

H

J

K

25.20

BSC

L

M

25.00

SQ

N

P

1.25
1.00
0.75	TOP VIEW

24.801.00 BSC

(BALL

PITCH)

1.00

BSC

BOTTOM VIEW

R

T

U

V

W

Y

AA

AB

AC

AD

3.10
2.94	DETAIL A
2.78
	0.97 BSC
NOTES:
1. ALL DIMENSIONS ARE IN MILLIMETERS.	SEATING PLANE

2.THE ACTUAL POSITION OF THE BALL GRID IS WITHIN 0.25 mm OF ITS IDEAL POSITION RELATIVE TO THE PACKAGE EDGES.

3.CENTER DIMENSIONS ARE NOMINAL.

4.THIS PACKAGE C ONFORMS TO JEDEC MS-034 SPECIFICATION.

1.60 MAX

0.60

0.50

0.40

0.75
0.75
			0.65			0.20 MAX

0.55
0.55
		(BALL
DIAMETER)

DETAIL A

Figure 47. 576-Ball BGA_ED (BP-576)

SURFACE MOUNT DESIGN

Table 36 is provided as an aid to PCB design. For industry- standard design recommendations, refer to IPC-7351, Generic Requirements for Surface Mount Design and Land Pattern Standard.

Table 36. BGA Data for Use with Surface Mount Design

Package	Ball Attach Type	Solder Mask Opening	Ball Pad Size
576-Ball BGA_ED	Nonsolder Mask Defined (NSMD)	0.69 mm diameter	0.56 mm diameter
(BP-576)

Rev. C Page 45 of 48 December 2006

Image 45

Contents ADSP-TS201S ADSP-TS201S Clock General-Purpose Algorithm Benchmarks at 600 MHzBenchmark Speed Cycles FIR filter per real tap 83 nsDual Compute Blocks Data Alignment Buffer DABDual Integer ALU Ialu DSP Memory Program SequencerInterrupt Controller Flexible Instruction SetInternal Space External Port OFF-CHIP MEMORY/PERIPHERALS InterfaceHost Interface DMA ControllerMultiprocessor Interface Sdram ControllerDMA controller provides these additional features Reset and Booting Timer and GENERAL-PURPOSE I/ONo Boot, Run from Memory Addresses Link Ports LvdsPower Domains Filtering Reference Voltage and ClocksDevelopment Tools Additional Information Evaluation KITSignal Type Term Description Pin Definitions-Clocks and ResetSclk Ratio RatioACK T/OD Pin Definitions-External Port Bus ControlsPin Definitions-External Port Arbitration Signal TypeDSP performs DMA transfers according to the DMA Pin Definitions-External Port DMA/FlybySample the data instead of the TigerSHARC MakesLdqm Pin Definitions-External Port Sdram ControllerHdqm SDA10Pin Definitions-JTAG Port Signal Type Term Description Pin Definitions-Flags, Interrupts, and TimerCONTROLIMP0 Pin Definitions-Link PortsCONTROLIMP1 DS1Driver Mode Pin Definitions-Power, Ground, and ReferenceDS2-0 Drive Output Pins Strength Impedance Impedance Control SelectionPin Definitions-I/O Strap Pins Type at Signal ResetPin Rstin = Sclkvref Operating ConditionsMaximum Duty Cycle for Input Transient Voltage Electrical CharacteristicsMaximum Duty VIN Max VIN Min Cycle2ESD Sensitivity Package InformationAbsolute Maximum Ratings Package Brand InformationAC Asynchronous Signal Specifications Timing SpecificationsGeneral AC Timing Reference Clocks-Core Clock Cclk Cycle TimeReference Clocks-JTAG Test Clock TCK Cycle Time Reference Clocks-System Clock Sclk Cycle TimeSclkrat = 5⋅, 7⋅ Parameter Description Min Max Unit Parameter Description Min Max UnitPower-Up Reset Timing Power-Up Timing1On-Chip Dram Refresh1 Normal Reset TimingOutputDisable Max AC Signal SpecificationsStrap Pins DS2-0 Static Pins-Must Be ConstantJtag SYS 11 Jtag System Pins +2.5 +10.0 +12.0 Strap SYS 9Link Port Lvds Receive Electrical Characteristics Link Port Lvds Transmit Electrical CharacteristicsParameter Description Test Conditions Min Max Unit VODParameter Description Min Max Unit Link Port-Data Out TimingLink Ports-Output Clock Link Ports-Transmission End and Stops LxBCMPI Hold Figure Link Port-Data In TimingLink Ports-Data Input Setup and Hold1 Typical Drive Currents at Strength Output Drive CurrentsTest Conditions Output Disable TimeCapacitive Loading Output Enable TimeTimes Andfall Rise Fall Time Thermal Characteristics for 25 mm × 25 mm Package Thermal CharacteristicsEnvironmental Conditions Parameter Condition Typical UnitBall Bgaed PIN Configurations Ball 25 mm × 25 mm Bgaed Ball Assignments Ball No Signal NameL0ACKO Sdcke SCLKRAT1L0DATI1N L0DATI3NID2 TDI TMR0E DS2 Enedreg TCKDS1 CONTROLIMP1 TDO FLAG3 L1CLKINNBGA Data for Use with Surface Mount Design Surface Mount DesignPackage Ball Attach Type Solder Mask Opening Ball Pad Size Ball Bgaed Nonsolder Mask Defined Nsmd Mm diameter BP-576Temperature Instruction On-Chip Package Model Range1 Rate2 Ordering GuideOperating Voltage Option Description Rev. C Page 47 of 48 December Rev. C Page 48 of 48 December