Teledyne 10 manual Electrical, Assembling, BioOptix

Page 20

BioOptix™ 10

Section 2 Installation

To keep tubing length at a minimum, buffer, sample, and waste collection containers should be placed to the left of the unit. The containers may also be kept behind the unit as long as the con- tainers are accessible.

The Foxy 200 should be installed to the right of the BioOptix 10. The fraction collector requires about 1800 square centimeters (275 in2) of bench space. Ensure that the full motion of the fraction collector arm is not obstructed.

The Windows PC may be placed anywhere within 2 meters of the

BioOptix 10 unit (the length of the serial control cable).

=Keep area clear for instrument connections, ventilation and to access On/Off Switch.

100 cm

16 cm

8 cm

(Rear)

33 cm

50 cm

16cm

8 cm

56 cm		BioOptix	61 cm
	13 cm	BioOptix	Foxy 200
	13 cm
10 cm	(Front)
10 cm	44 cm	12 cm	29 cm
10 cm

Figure 2-1 System space requirements

2.2.2	Electrical	The operating voltage of the BioOptix 10 is factory set. Refer to
	Requirements	the serial number label on the right side panel to determine the
		electrical requirements.
		Teledyne Isco recommends that the BioOptix 10 system runs on
		a dedicated AC circuit to prevent abnormal conditions that may
		be caused by high current or electrical noise. The BioOptix 10
		and Foxy 200 should be connected to the same circuit to prevent
		ground loop anomalies.
2.2.3	Assembling the	The BioOptix 10 is shipped in two pieces—a column module and
	BioOptix 10	a pump module. After unpacking and inspecting the modules
		place them as shown in Figure 2-2 on a sturdy work surface. This
		will allow access to the internal electrical and fluid connections.

2-2

Image 20

Contents BioOptix Page Foreword Page General Warnings Application, take heed in the following general warningsDamage Hazard Symbols Symboles de sécuritéBioOptix 10 Safety Table of Contents BioOptixSystem Maintenance Appendix B Fluid Path DiagramsAppendix C Replacement Parts Lists Appendix a Method TemplatesList of Figures List of Tables Introduction Product OverviewBioOptix 10 Specifications Maximum Altitude 2000 metersBioOptix 10 Front Panel Controls System Controls and ConnectorsBioOptix 10 Front Panel Controls BioOptix 10 Left-side Connections BioOptix 10 Left-side Controls and ConnectionsBioOptix 10 Right-side Connections BioOptix 10 Right-side ConnectionsBioOptix 10 Rear Panel Controls and Connections BioOptix 10 Rear Panel Controls and ConnectionsInstallation BioOptix 10 InstallationUnpacking the BioOptix 10 System SpaceBioOptix ElectricalAssembling Accessing pump and column module internal connections Routing the Sample Out lines column module P110 Connection on BD3 AC power connection from pump module 10 Liquid connections pump module shown 11 Aligning the fasteners Ceeding with the arm assembly instructions FoxyBioOptix Installation Common Buffer Inlet Mounting Block Manifold Tubing Color chart Channel Numbers Color Part Number16 Foxy 200 tubing connections BioOptix 10 Software ConfiguringWindows PC Minimum Requirements BioOptix 10 System Preparation 18 Column bypass tubing 20 BioOptix 10 Manual Hardware Control window BioOptix Installation Adapters Sample Preparation Column InstallationOperation Overview BioOptix 10 SoftwareGradients Methods Defining a Gradient To define a gradientEquilibrate tab settings Load Settings This block loads the sample onto the column Load tab settingsWash Settings Flush Settings ExperimentsSetting up Running ExperimentOperation Buttons FileZoom and pan OperationPost-experiment Operation Pump FlushSaving Run Data PreviewAutoReports BioOptix 10 Operation System Maintenance Vent damageExterior Cleaning Piston Seal Replacement Refer to -3 for the following steps Pump assembly components Deuterium Lamp Replacement Waste port mounting plate Operating Problems TroubleshootingCommon Problems Inaccessible Fuses Circuit breaker location Teledyne Isco, Inc Service DepartmentHow to Ship Returns Appendix a Method Templates Dard.tpl Modifying Template General Editing RulesOther BlocksBlockn Appendix B Fluid Path Diagrams Fluid-type BlocksBioOptix Appendix B Fluid Path Diagrams Load-type BlocksFigure B-4 Fluid path for Load-type blocks Manual injections Plumbing Diagram Pump FlushFigure B-7 BioOptix 10 Plumbing Diagram BioOptix Appendix B Fluid Path Diagrams Appendix C Replacement Parts Lists BioOptix Appendix C Replacement Parts Lists Detector Assembly 13BioOptix 10 Replacement Parts Lists 13BioOptix 10 Replacement Parts Lists 13BioOptix 10 Replacement Parts Lists Column Module 13BioOptix 10 Replacement Parts Lists 13BioOptix 10 Replacement Parts Lists 13BioOptix 10 Replacement Parts Lists Pump Module 13BioOptix 10 Replacement Parts Lists 13BioOptix 10 Replacement Parts Lists 13BioOptix 10 Replacement Parts Lists Declaration of Conformity Page Teledyne Isco One Year Limited Factory Service Warranty