Teledyne 10 manual Service Department, How to Ship Returns, Teledyne Isco, Inc

Page 60

BioOptix™ 10

Section 4 System Maintenance

4.6 Service Department

If you have a problem with the instrument or need parts infor- mation, contact Isco’s Service Department. If you write, please include all pertinent information that may be helpful in solving your problem. Address your letter to:

Teledyne Isco, Inc.

Service Department

P.O. Box 82531

Lincoln, NE 68505

4.7 How to Ship Returns

Before deciding to return the unit for factory repair, we suggest that you call the Service Department. Often a problem can be solved in the field with just a little extra help from our service technicians. Our telephone number is:

Toll free: (800) 228-4373 (USA and Canada) (402) 464-0231

If you prefer, you can send an e-mail detailing your problem to:

service@isco.com

Other contact information can be obtained from our Web site at:

http://www.isco.com

Be sure all parts and hardware are back in place before packing. Wrap the unit in heavy paper or put it in a plastic bag. If the original shipping carton is not available, put the wrapped unit in a strong cardboard box at least six inches longer in each basic dimension than the unit itself. Fill the box equally around the unit with resilient packing material (shredded paper, bubble pack, expanded foam chunks, etc.). Seal the box with strapping tape or gummed cloth tape and ship it to the address given on the warranty page. The warranty at the end of the manual describes the conditions under which Teledyne Isco will pay surface shipping costs.

It is very important that the unit be well-packaged for shipping and fully insured. Damage claims must be resolved by you and the carrier. Damage in shipment due to inadequate packing can delay the repair and return of the unit to you.

4-10

Image 60
Contents BioOptix Page Foreword Page General Warnings Application, take heed in the following general warningsDamage Hazard Symbols Symboles de sécuritéBioOptix 10 Safety Table of Contents BioOptixSystem Maintenance Appendix B Fluid Path DiagramsAppendix C Replacement Parts Lists Appendix a Method TemplatesList of Figures List of Tables Introduction Product OverviewBioOptix 10 Specifications Maximum Altitude 2000 metersSystem Controls and Connectors BioOptix 10 Front Panel ControlsBioOptix 10 Front Panel Controls BioOptix 10 Left-side Connections BioOptix 10 Left-side Controls and ConnectionsBioOptix 10 Right-side Connections BioOptix 10 Right-side ConnectionsBioOptix 10 Rear Panel Controls and Connections BioOptix 10 Rear Panel Controls and ConnectionsInstallation BioOptix 10 InstallationUnpacking the BioOptix 10 System SpaceElectrical AssemblingBioOptix Accessing pump and column module internal connections Routing the Sample Out lines column module P110 Connection on BD3 AC power connection from pump module 10 Liquid connections pump module shown 11 Aligning the fasteners Ceeding with the arm assembly instructions FoxyBioOptix Installation Common Buffer Inlet Mounting Block Manifold Tubing Color chart Channel Numbers Color Part Number16 Foxy 200 tubing connections Configuring Windows PC Minimum RequirementsBioOptix 10 Software BioOptix 10 System Preparation 18 Column bypass tubing 20 BioOptix 10 Manual Hardware Control window BioOptix Installation Sample Preparation Column Installation OperationAdapters BioOptix 10 Software GradientsOverview Methods Defining a Gradient To define a gradientEquilibrate tab settings Load Settings This block loads the sample onto the column Load tab settingsWash Settings Flush Settings ExperimentsSetting up Running ExperimentOperation Buttons FileZoom and pan OperationPost-experiment Operation Pump FlushSaving Run Data PreviewAutoReports BioOptix 10 Operation System Maintenance Vent damageExterior Cleaning Piston Seal Replacement Refer to -3 for the following steps Pump assembly components Deuterium Lamp Replacement Waste port mounting plate Troubleshooting Common ProblemsOperating Problems Inaccessible Fuses Circuit breaker location Service Department How to Ship ReturnsTeledyne Isco, Inc Appendix a Method Templates Dard.tpl Modifying Template General Editing RulesBlocks BlocknOther Appendix B Fluid Path Diagrams Fluid-type BlocksBioOptix Appendix B Fluid Path Diagrams Load-type BlocksFigure B-4 Fluid path for Load-type blocks Manual injections Plumbing Diagram Pump FlushFigure B-7 BioOptix 10 Plumbing Diagram BioOptix Appendix B Fluid Path Diagrams Appendix C Replacement Parts Lists BioOptix Appendix C Replacement Parts Lists Detector Assembly 13BioOptix 10 Replacement Parts Lists 13BioOptix 10 Replacement Parts Lists 13BioOptix 10 Replacement Parts Lists Column Module 13BioOptix 10 Replacement Parts Lists 13BioOptix 10 Replacement Parts Lists 13BioOptix 10 Replacement Parts Lists Pump Module 13BioOptix 10 Replacement Parts Lists 13BioOptix 10 Replacement Parts Lists 13BioOptix 10 Replacement Parts Lists Declaration of Conformity Page Teledyne Isco One Year Limited Factory Service Warranty