Teledyne 10 manual General Warnings, Application, take heed in the following general warnings

Page 5

	BioOptix™ 10
	Safety

General Warnings	Before installing, operating, or maintaining this equipment, it is
	imperative that all hazards and preventive measures are fully
	understood. While specific hazards may vary according to location
	and application, take heed in the following general warnings:

	WARNING
	Liquids associated with this instrument may be classified
	as carcinogenic, biohazardous, flammable, or radioactive.
	Should these liquids be used, it is highly recommended that
	this application be accomplished in an isolated
	environment designed for these types of materials in
	accordance with federal, state, and local regulatory laws,
	and in compliance with your company’s chemical/hygiene
	plan in the event of a spill.

	AVERTISSEMENT
	Eviter de répandre des liquides dangereux. Les liquides qui
	sont analysés dans cet instrument peuvent être
	cancérigènes, hasards biologiques, inflammables, ou
	radioactifs. Si vous devez utiliser tels liquides, il est très
	recommandé que vous le faites à l'intérieur d'un
	environnement isolé conçu pour tels liquides. Cet
	environnement isolé devrait être construit selon les
	règlements fédéraux, provinciaux, et locaux, aussi que le
	plan de votre compagnie qui concerne l'évènement d'un
	accident avec les matières hasardeuses.

	WARNING
	Avoid hazardous practices! If you use this instrument in
	any way not specified in this manual, the protection
	provided by the instrument may be impaired.

	AVERTISSEMENT
	Éviter les usages périlleux! Si vous utilisez cet instrument
	d’une manière autre que celles qui sont specifiées dans ce
	manuel, la protection fournie de l’instrument peut être
	affaiblie; cela augmentera votre risque de blessure.

	WARNING
	If this system uses flammable organic solvents, Teledyne
	Isco recommends that you place this system in a
	well-ventilated environment, designed for these types of
	materials. This environment should be constructed in
	accordance with federal, state, and local regulations. It
	should also comply with your organization’s plan
	concerning chemical and hygiene mishaps. In all cases use
	good laboratory practices and standard safety procedures.

iii

Image 5

Contents BioOptix Page Foreword Page Application, take heed in the following general warnings General WarningsDamage Symboles de sécurité Hazard SymbolsBioOptix 10 Safety BioOptix Table of ContentsAppendix B Fluid Path Diagrams System MaintenanceAppendix C Replacement Parts Lists Appendix a Method TemplatesList of Figures List of Tables Product Overview IntroductionMaximum Altitude 2000 meters BioOptix 10 SpecificationsBioOptix 10 Front Panel Controls System Controls and ConnectorsBioOptix 10 Front Panel Controls BioOptix 10 Left-side Controls and Connections BioOptix 10 Left-side ConnectionsBioOptix 10 Right-side Connections BioOptix 10 Right-side ConnectionsBioOptix 10 Rear Panel Controls and Connections BioOptix 10 Rear Panel Controls and ConnectionsBioOptix 10 Installation InstallationUnpacking the BioOptix 10 System SpaceBioOptix ElectricalAssembling Accessing pump and column module internal connections Routing the Sample Out lines column module P110 Connection on BD3 AC power connection from pump module 10 Liquid connections pump module shown 11 Aligning the fasteners Foxy Ceeding with the arm assembly instructionsBioOptix Installation Common Buffer Inlet Mounting Block Manifold Channel Numbers Color Part Number Tubing Color chart16 Foxy 200 tubing connections BioOptix 10 Software ConfiguringWindows PC Minimum Requirements BioOptix 10 System Preparation 18 Column bypass tubing 20 BioOptix 10 Manual Hardware Control window BioOptix Installation Adapters Sample Preparation Column InstallationOperation Overview BioOptix 10 SoftwareGradients Defining a Gradient To define a gradient MethodsEquilibrate tab settings Load tab settings Load Settings This block loads the sample onto the columnWash Settings Experiments Flush SettingsSetting up Experiment RunningOperation Buttons FileOperation Zoom and panPump Flush Post-experiment OperationPreview Saving Run DataAutoReports BioOptix 10 Operation Vent damage System MaintenanceExterior Cleaning Piston Seal Replacement Refer to -3 for the following steps Pump assembly components Deuterium Lamp Replacement Waste port mounting plate Operating Problems TroubleshootingCommon Problems Inaccessible Fuses Circuit breaker location Teledyne Isco, Inc Service DepartmentHow to Ship Returns Appendix a Method Templates Dard.tpl General Editing Rules Modifying TemplateOther BlocksBlockn Fluid-type Blocks Appendix B Fluid Path DiagramsLoad-type Blocks BioOptix Appendix B Fluid Path DiagramsFigure B-4 Fluid path for Load-type blocks Manual injections Pump Flush Plumbing DiagramFigure B-7 BioOptix 10 Plumbing Diagram BioOptix Appendix B Fluid Path Diagrams Appendix C Replacement Parts Lists BioOptix Appendix C Replacement Parts Lists Detector Assembly 13BioOptix 10 Replacement Parts Lists 13BioOptix 10 Replacement Parts Lists 13BioOptix 10 Replacement Parts Lists Column Module 13BioOptix 10 Replacement Parts Lists 13BioOptix 10 Replacement Parts Lists 13BioOptix 10 Replacement Parts Lists Pump Module 13BioOptix 10 Replacement Parts Lists 13BioOptix 10 Replacement Parts Lists 13BioOptix 10 Replacement Parts Lists Declaration of Conformity Page Teledyne Isco One Year Limited Factory Service Warranty