Cypress CY7C67200 manual Transmit Ready Bit, Packet Mode Select Bit, Receive Overflow Flag Bit

Page 45

CY7C67200

Transmit Ready (Bit 4)

The Transmit Ready bit is a read only bit that indicates if the HSS Transmit FIFO is ready for the CPU to load new data for transmission.

1:HSS transmit FIFO ready for loading

0:HSS transmit FIFO not ready for loading

Packet Mode Select (Bit 3)

The Packet Mode Select bit selects between Receive Packet Ready and Receive Ready as the interrupt source for the RxIntr interrupt.

1:Selects Receive Packet Ready as the source

0:Selects Receive Ready as the source

Receive Overflow Flag (Bit 2)

The Receive Overflow Flag bit indicates if the Receive FIFO overflowed when set. This flag can be cleared by writing a ‘1’ to this bit.

1:Overflow occurred

0:Overflow did not occur

Receive Packet Ready Flag (Bit 1)

The Receive Packet Ready Flag bit is a read only bit that indicates if the HSS receive FIFO is full with eight bytes.

1:HSS receive FIFO is full

0:HSS receive FIFO is not full

Receive Ready Flag (Bit 0)

The Receive Ready Flag is a read only bit that indicates if the HSS receive FIFO is empty.

1:HSS receive FIFO is not empty (one or more bytes is reading for reading)

0:HSS receive FIFO is empty

HSS Baud Rate Register [0xC072] [R/W]

Figure 49. HSS Baud Rate Register

Bit #	15	14	13	12	11	10	9	8
Field		Reserved				Baud...
Read/Write	-	-	-	R/W	R/W	R/W	R/W	R/W
Default	0	0	0	0	0	0	0	0

Bit #	7	6	5	4		3	2	1	0
Field					...Baud
Read/Write	R/W	R/W	R/W	R/W		R/W	R/W	R/W	R/W
Default	0	0	0	1		0	1	1	1

Register Description

The HSS Baud Rate register sets the HSS Baud Rate. At reset, the default value is 0x0017 which sets the baud rate to 2.0 MHz.

Baud (Bits [12:0])

The Baud field is the baud rate divisor minus one, in units of 1/48 MHz. Therefore the Baud Rate = 48 MHz/(Baud + 1). This puts a constraint on the Baud Value as follows: (24 – 1) < Baud > (5000 – 1)

Reserved

All reserved bits must bit written as ‘0’.

Document #: 38-08014 Rev. *G

Page 45 of 78

[+] Feedback

Image 45

Contents Typical Applications EZ-OTG FeaturesCY7C67200 CY16Introduction Processor Core Functional OverviewInterface Descriptions OTG Interface Pins Pin Name Pin Number USB Interface Pins Pin Name Pin NumberUSB Interface OTG InterfaceSPI Interface Pins Pin Name Pin Number I2C Eeprom Interface Pins Pin Name Pin NumberHSS Interface Pins Pin Name Pin Number Serial Peripheral InterfaceHost Port Interface HPI HPI Interface Pins 1 Pin Name Pin NumberHPI Addressing HPI A10 Charge Pump InterfaceCharge Pump Interface Pins Pin Name Pin Number Booster InterfaceCrystal Interface Boot Configuration Interface Crystal Pins Pin Name Pin NumberBoot Mode PinPower Savings and Reset Description Power Savings Mode DescriptionSleep Memory Map Registers Bank Register Example Hex Value Binary Value Bank Register 0xC002 R/WReserved Hardware Revision Register 0xC004 RCPU Speed Definition Processor Speed CPU Speed Register 0xC008 R/WHost/Device 1 Wake Enable Bit Host/Device 2 Wake Enable BitOTG Wake Enable Bit HSS Wake Enable BitOTG Interrupt Enable Bit Halt Enable BitSPI Interrupt Enable Bit Host/Device 2 Interrupt Enable BitGpio Interrupt Enable Bit Uart Interrupt Enable BitTimer 1 Interrupt Enable Bit Timer 0 Interrupt Enable BitPort 1A Diagnostic Enable Bit Port 2A Diagnostic Enable BitPull-down Enable Bit LS Pull-up Enable BitLock Enable Bit Timeout Flag BitWDT Enable Bit Reset Strobe BitGeneral USB Registers Timer n Register R/WUSB Registers Register Name Address SIE1/SIE2 0xC08A/0xC0AAPort a Resistors Enable Bit Mode Select BitUSB Data Line Pull-up and Pull-down Resistors Mode Port n Resistors Function Select EnableSync Enable Bit Preamble Enable BitISO Enable Bit Arm Enable BitHost n Address Register R/W Host n Count Register R/WHost 1 Count Register 0xC084 Host 2 Count Register 0xC0A4 Underflow Flag Bit Error Flag BitStall Flag Bit NAK Flag BitHost n PID Register W ACK Flag BitPID Select Definition PID SelectHost n Device Address Register W Host n Count Result Register RID Interrupt Enable Bit Vbus Interrupt Enable BitSOF/EOP Interrupt Enable Bit Port a Wake Interrupt Enable BitID Interrupt Flag Bit Vbus Interrupt Flag BitSOF/EOP Interrupt Flag Bit Port a Wake Interrupt Flag BitHost n SOF/EOP Count Register R/W Count Bits Count field sets the SOF/EOP counter durationHost n SOF/EOP Counter Register R USB Device Only Registers Reserved Host n Frame Register RUSB Device Only Registers Register Name Address Device 1/DeviceStall Enable Bit IN/OUT Ignore Enable BitNAK Interrupt Enable Bit Enable BitDevice n Endpoint n Count Register R/W Device n Endpoint n Address Register R/WOUT Exception Flag Bit Device n Endpoint n Status Register R/WTimeout occurred Timeout condition did not occur Setup Flag BitError occurred Error did not occur Exception Flag BitDevice n Endpoint n Count Result Register Device n Endpoint n Count Result Register R/WSOF/EOP Timeout Interrupt Enable Bit Device n Interrupt Enable Register R/WReset Interrupt Enable Bit EP7 Interrupt Enable BitEP4 Interrupt Enable Bit EP5 Interrupt Enable Bit EP2 Interrupt Enable BitEP3 Interrupt Enable Bit EP1 Interrupt Enable BitDevice n Status Register R/W Device n Address Register WEP7 Interrupt Flag Bit Reset Interrupt Flag BitEP6 Interrupt Flag Bit EP5 Interrupt Flag BitSOF/EOP Timeout Interrupt Counter Bits SOF/EOP Timeout Flag BitDevice n Frame Number Register R Device n SOF/EOP Count Register WReceive Disable Bit Vbus Pull-up Enable BitCharge Pump Enable Bit Vbus Discharge Enable BitSAS Enable Bit Write Protect Enable BitMode Select Definition Gpio Configuration 108 111 Reserved Vbus Valid Flag BitSPI Enable Bit HSS Enable BitInterrupt 0 Enable Bit Interrupt 0 Polarity Select BitGpio 0 Input Data Register 0xC020 R Gpio 1 Input Data Register 0xC026 RGpio 0 Direction Register 0xC022 R/W Gpio 1 Direction Register 0xC028 R/W HSS RegistersHSS Registers Register Name Address CTS Enable Bit Xoff Enable BitReceive Interrupt Enable Bit RTS Polarity Select BitTransmit Ready Bit Packet Mode Select BitReceive Overflow Flag Bit Receive Packet Ready Flag BitHSS Transmit Gap Register 0xC074 R/W Transmit Gap Select BitsHSS Data Register 0xC076 R/W HSS Receive Counter Register 0xC07A R/W HSS Receive Address Register 0xC078 R/WHSS Transmit Counter Register 0xC07E R/W HSS Transmit Address Register 0xC07C R/WHPI Registers HPI Registers Register Name AddressID to HPI Enable Bit Vbus to HPI Enable BitSOF/EOP2 to HPI Enable Bit HPI Breakpoint Register 0x0140 RSOF/EOP1 to HPI Enable Bit SOF/EOP2 to CPU Enable BitSOF/EOP1 to CPU Enable Bit Reset2 to HPI Enable BitSIE1msg Register SIE2msg Register SIEXmsg Register WData Bits HPI Mailbox Register 0xC0C6 R/WVbus Flag Bit Reset2 Flag BitID Flag Bit SOF/EOP2 Flag BitDone1 Flag Bit SPI Registers Reset1 Flag BitMailbox Out Flag Bit SPI Registers Register Name AddressPhase Select Bit 3Wire Enable BitMaster Active Enable Bit Master Enable BitRead Enable Bit Byte Mode BitSCK Strobe Bit Fifo Init BitTransfer Interrupt Enable Bit Transmit Interrupt Enable BitFifo Error Flag Bit Receive Bit Length BitsTransmit Interrupt Flag Bit CRC Mode Definition CRCMode CRC PolynomialTransfer Interrupt Flag Bit Transmit Interrupt Clear BitCRC Clear Bit CRC Enable BitReceive CRC Bit One in CRC BitSPI Transmit Count Register 0xC0DA R/W SPI Transmit Address Register 0xC0D8 R/WSPI Receive Count Register 0xC0DE R/W SPI Receive Address Register 0xC0DC R/WUart Registers Uart Registers Register Name AddressScale Select Bit Uart Enable BitBaud Select Bits Uart Baud Select Definition Baud Rate DIV8 =Uart Data Register 0xC0E4 R/W Transmit Full BitPin Diagram Pin DescriptionsPin Descriptions Name Type A1 HPI A1 GPIO20 General Purpose IOGPIO19 General Purpose IO A0 HPI A0Absolute Maximum Ratings Booster Power Input 2.7V toOperating Conditions Crystal Requirements XTALIN, XtaloutDC Characteristics Reset Timing AC Timing CharacteristicsClock Timing I2C Eeprom TimingParameter Description Min Typical Max Unit HPI Host Port Interface Write Cycle Timing HPI Host Port Interface Read Cycle Timing Data Access Time, from HPInRD fallingRead Pulse Width Read Cycle Time Document # 38-08014 Rev. *GHSS Byte Mode Transmit HSS Block Mode TransmitHSS Byte and Block Mode Receive Hssrts Hsscts Hardware CTS/RTS HandshakeRegister Summary Register SummaryGPIO31 GPIO30 GPIO29 SE0 SOF/EOP2 Ordering Information Package DiagramOrdering Information Ordering Code Package Type PB-Free Ball 7.00 mm x 7.00 mm x 1.2 mm Fbga BA48Document History Issue Orig. Description of Change Date