Cypress CY7C67200 manual SOF/EOP2

Page 76

CY7C67200

Table 42. Register Summary (continued)

R/W	Address	Register	Bit 15	Bit 14	Bit 13	Bit 12	Bit 11	Bit 10	Bit 9	Bit 8	Default High
			Bit 7	Bit 6	Bit 5	Bit 4	Bit 3	Bit 2	Bit 1	Bit 0	Default Low
R/W	0xC0D6	SPI Data Port t	Reserved								xxxx xxxx
			Data								xxxx xxxx
R/W	0xC0D8	SPI Transmit Address	Address...								0000 0000
			...Address								0000 0000
R/W	0xC0DA	SPI Transmit Count	Reserved					Count...			0000 0000
			...Count								0000 0000
R/W	0xC0DC	SPI Receive Address	Address...								0000 0000
			...Address								0000 0000
R/W	0xC0DE	SPI Receive Count	Reserved					Count...			0000 0000
			...Count								0000 0000
R/W	0xC0E0	UART Control	Reserved...								0000 0000
			...Reserved			Scale	Baud			UART	0000 0111
						Select	Select			Enable
R	0xC0E2	UART Status	Reserved...								0000 0000
			...Reserved						Receive	Transmit	0000 0000
									Full	Full
R/W	0xC0E4	UART Data	Reserved								0000 0000
			Data								0000 0000
R		HPI Status Port	VBUS	ID	Reserved	SOF/EOP2	Reserved	SOF/EOP1	Reset2	Mailbox In
			Flag	Flag		Flag		Flag	Flag	Flag
			Resume2	Resume1	SIE2msg	SIE1msg	Done2	Done1	Reset1	Mailbox Out
			Flag	Flag			Flag	Flag	Flag	Flag

Document #: 38-08014 Rev. *G

Page 76 of 78

[+] Feedback

Image 76

Contents EZ-OTG Features Typical ApplicationsCY7C67200 CY16Processor Core Functional Overview IntroductionInterface Descriptions USB Interface Pins Pin Name Pin Number OTG Interface Pins Pin Name Pin NumberUSB Interface OTG InterfaceI2C Eeprom Interface Pins Pin Name Pin Number SPI Interface Pins Pin Name Pin NumberHSS Interface Pins Pin Name Pin Number Serial Peripheral InterfaceHPI Interface Pins 1 Pin Name Pin Number Host Port Interface HPIHPI Addressing HPI A10 Charge Pump InterfaceBooster Interface Charge Pump Interface Pins Pin Name Pin NumberCrystal Interface Crystal Pins Pin Name Pin Number Boot Configuration InterfaceBoot Mode PinPower Savings Mode Description Power Savings and Reset DescriptionSleep Memory Map Registers Bank Register 0xC002 R/W Bank Register Example Hex Value Binary ValueReserved Hardware Revision Register 0xC004 RCPU Speed Register 0xC008 R/W CPU Speed Definition Processor SpeedHost/Device 2 Wake Enable Bit Host/Device 1 Wake Enable BitOTG Wake Enable Bit HSS Wake Enable BitHalt Enable Bit OTG Interrupt Enable BitSPI Interrupt Enable Bit Host/Device 2 Interrupt Enable BitUart Interrupt Enable Bit Gpio Interrupt Enable BitTimer 1 Interrupt Enable Bit Timer 0 Interrupt Enable BitPort 2A Diagnostic Enable Bit Port 1A Diagnostic Enable BitPull-down Enable Bit LS Pull-up Enable BitTimeout Flag Bit Lock Enable BitWDT Enable Bit Reset Strobe BitTimer n Register R/W General USB RegistersUSB Registers Register Name Address SIE1/SIE2 0xC08A/0xC0AAMode Select Bit Port a Resistors Enable BitUSB Data Line Pull-up and Pull-down Resistors Mode Port n Resistors Function Select EnablePreamble Enable Bit Sync Enable BitISO Enable Bit Arm Enable BitHost n Count Register R/W Host n Address Register R/WHost 1 Count Register 0xC084 Host 2 Count Register 0xC0A4 Error Flag Bit Underflow Flag BitStall Flag Bit NAK Flag BitACK Flag Bit Host n PID Register WPID Select Definition PID SelectHost n Count Result Register R Host n Device Address Register WVbus Interrupt Enable Bit ID Interrupt Enable BitSOF/EOP Interrupt Enable Bit Port a Wake Interrupt Enable BitVbus Interrupt Flag Bit ID Interrupt Flag BitSOF/EOP Interrupt Flag Bit Port a Wake Interrupt Flag BitCount Bits Count field sets the SOF/EOP counter duration Host n SOF/EOP Count Register R/WHost n SOF/EOP Counter Register R Host n Frame Register R USB Device Only Registers ReservedUSB Device Only Registers Register Name Address Device 1/DeviceIN/OUT Ignore Enable Bit Stall Enable BitNAK Interrupt Enable Bit Enable BitDevice n Endpoint n Address Register R/W Device n Endpoint n Count Register R/WDevice n Endpoint n Status Register R/W OUT Exception Flag BitSetup Flag Bit Timeout occurred Timeout condition did not occurError occurred Error did not occur Exception Flag BitDevice n Endpoint n Count Result Register R/W Device n Endpoint n Count Result RegisterDevice n Interrupt Enable Register R/W SOF/EOP Timeout Interrupt Enable BitReset Interrupt Enable Bit EP7 Interrupt Enable BitEP5 Interrupt Enable Bit EP2 Interrupt Enable Bit EP4 Interrupt Enable BitEP3 Interrupt Enable Bit EP1 Interrupt Enable BitDevice n Address Register W Device n Status Register R/WReset Interrupt Flag Bit EP7 Interrupt Flag BitEP6 Interrupt Flag Bit EP5 Interrupt Flag BitSOF/EOP Timeout Flag Bit SOF/EOP Timeout Interrupt Counter BitsDevice n Frame Number Register R Device n SOF/EOP Count Register WVbus Pull-up Enable Bit Receive Disable BitCharge Pump Enable Bit Vbus Discharge Enable BitWrite Protect Enable Bit SAS Enable BitMode Select Definition Gpio Configuration 108 111 Reserved Vbus Valid Flag BitHSS Enable Bit SPI Enable BitInterrupt 0 Enable Bit Interrupt 0 Polarity Select BitGpio 1 Input Data Register 0xC026 R Gpio 0 Input Data Register 0xC020 RGpio 0 Direction Register 0xC022 R/W HSS Registers Gpio 1 Direction Register 0xC028 R/WHSS Registers Register Name Address Xoff Enable Bit CTS Enable BitReceive Interrupt Enable Bit RTS Polarity Select BitPacket Mode Select Bit Transmit Ready BitReceive Overflow Flag Bit Receive Packet Ready Flag BitTransmit Gap Select Bits HSS Transmit Gap Register 0xC074 R/WHSS Data Register 0xC076 R/W HSS Receive Address Register 0xC078 R/W HSS Receive Counter Register 0xC07A R/WHSS Transmit Address Register 0xC07C R/W HSS Transmit Counter Register 0xC07E R/WHPI Registers HPI Registers Register Name AddressVbus to HPI Enable Bit ID to HPI Enable BitSOF/EOP2 to HPI Enable Bit HPI Breakpoint Register 0x0140 RSOF/EOP2 to CPU Enable Bit SOF/EOP1 to HPI Enable BitSOF/EOP1 to CPU Enable Bit Reset2 to HPI Enable BitSIEXmsg Register W SIE1msg Register SIE2msg RegisterData Bits HPI Mailbox Register 0xC0C6 R/WReset2 Flag Bit Vbus Flag BitID Flag Bit SOF/EOP2 Flag BitSPI Registers Reset1 Flag Bit Done1 Flag BitMailbox Out Flag Bit SPI Registers Register Name Address3Wire Enable Bit Phase Select BitMaster Active Enable Bit Master Enable BitByte Mode Bit Read Enable BitSCK Strobe Bit Fifo Init BitTransmit Interrupt Enable Bit Transfer Interrupt Enable BitFifo Error Flag Bit Receive Bit Length BitsCRC Mode Definition CRCMode CRC Polynomial Transmit Interrupt Flag BitTransfer Interrupt Flag Bit Transmit Interrupt Clear BitCRC Enable Bit CRC Clear BitReceive CRC Bit One in CRC BitSPI Transmit Address Register 0xC0D8 R/W SPI Transmit Count Register 0xC0DA R/WSPI Receive Address Register 0xC0DC R/W SPI Receive Count Register 0xC0DE R/WUart Registers Uart Registers Register Name AddressUart Enable Bit Scale Select BitBaud Select Bits Uart Baud Select Definition Baud Rate DIV8 =Transmit Full Bit Uart Data Register 0xC0E4 R/WPin Descriptions Pin DiagramPin Descriptions Name Type GPIO20 General Purpose IO A1 HPI A1GPIO19 General Purpose IO A0 HPI A0Booster Power Input 2.7V to Absolute Maximum RatingsOperating Conditions Crystal Requirements XTALIN, XtaloutDC Characteristics AC Timing Characteristics Reset TimingI2C Eeprom Timing Clock TimingParameter Description Min Typical Max Unit HPI Host Port Interface Write Cycle Timing Data Access Time, from HPInRD falling HPI Host Port Interface Read Cycle TimingRead Pulse Width Read Cycle Time Document # 38-08014 Rev. *GHSS Block Mode Transmit HSS Byte Mode TransmitHSS Byte and Block Mode Receive Hardware CTS/RTS Handshake Hssrts HssctsRegister Summary Register SummaryGPIO31 GPIO30 GPIO29 SE0 SOF/EOP2 Package Diagram Ordering InformationOrdering Information Ordering Code Package Type PB-Free Ball 7.00 mm x 7.00 mm x 1.2 mm Fbga BA48Issue Orig. Description of Change Date Document History