Cypress CY7C67200 manual ACK Flag Bit, Host n PID Register W, PID Select Definition

Page 23

CY7C67200

ACK Flag (Bit 0)

The ACK Flag bit indicates two different conditions depending on the transfer type. For non-Isochronous transfers, this bit represents a transaction ending by receiving or sending an ACK packet. For Isochronous transfers, this bit represents a successful transaction that will not be represented by an ACK packet.

1:For non-Isochronous transfers, the transaction was ACKed. For Isochronous transfers, the transaction was completed successfully.

0:For non-Isochronous transfers, the transaction was not ACKed. For Isochronous transfers, the transaction was not completed successfully.

Host n PID Register [W]

•Host 1 PID Register 0xC086

•Host 2 PID Register 0xC0A6

Figure 22. Host n PID Register

Bit #	15	14	13	12		11	10	9	8
Field					Reserved
Read/Write	-	-	-	-		-	-	-	-
Default	0	0	0	0		0	0	0	0

Bit #	7	6		5	4	3	2	1	0
Field			PID Select				Endpoint Select
Read/Write	W	W		W	W	W	W	W	W
Default	0	0		0	0	0	0	0	0

Register Description

The Host n PID register is a write-only register that provides the PID and Endpoint information to the USB SIE to be used in the next transaction.

PID Select (Bits [7:4])

The PID Select field defined as in Table 26. ACK and NAK tokens are automatically sent based on settings in the Host n Control register and do not need to be written in this register.

Table 26.PID Select Definition

PID TYPE	PID Select [7:4]
set-up	1101 (D Hex)

IN	1001 (9 Hex)

OUT	0001 (1 Hex)

SOF	0101 (5 Hex)

Table 26.PID Select Definition		(continued)

PID TYPE		PID Select [7:4]
PREAMBLE		1100 (C Hex)

NAK		1010 (A Hex)

STALL		1110 (E Hex)

DATA0		0011 (3 Hex)

DATA1		1011 (B Hex)

Endpoint Select (Bits [3:0])

The Endpoint field allows addressing of up to 16 different endpoints.

Reserved

All reserved bits must be written as ‘0’.

Document #: 38-08014 Rev. *G

Page 23 of 78

[+] Feedback

Image 23

Contents CY16 EZ-OTG FeaturesTypical Applications CY7C67200Interface Descriptions IntroductionProcessor Core Functional Overview OTG Interface USB Interface Pins Pin Name Pin NumberOTG Interface Pins Pin Name Pin Number USB InterfaceSerial Peripheral Interface I2C Eeprom Interface Pins Pin Name Pin NumberSPI Interface Pins Pin Name Pin Number HSS Interface Pins Pin Name Pin NumberCharge Pump Interface HPI Interface Pins 1 Pin Name Pin NumberHost Port Interface HPI HPI Addressing HPI A10Crystal Interface Charge Pump Interface Pins Pin Name Pin NumberBooster Interface Pin Crystal Pins Pin Name Pin NumberBoot Configuration Interface Boot ModeSleep Power Savings and Reset DescriptionPower Savings Mode Description Memory Map Registers Hardware Revision Register 0xC004 R Bank Register 0xC002 R/WBank Register Example Hex Value Binary Value ReservedCPU Speed Definition Processor Speed CPU Speed Register 0xC008 R/WHSS Wake Enable Bit Host/Device 2 Wake Enable BitHost/Device 1 Wake Enable Bit OTG Wake Enable BitHost/Device 2 Interrupt Enable Bit Halt Enable BitOTG Interrupt Enable Bit SPI Interrupt Enable BitTimer 0 Interrupt Enable Bit Uart Interrupt Enable BitGpio Interrupt Enable Bit Timer 1 Interrupt Enable BitLS Pull-up Enable Bit Port 2A Diagnostic Enable BitPort 1A Diagnostic Enable Bit Pull-down Enable BitReset Strobe Bit Timeout Flag BitLock Enable Bit WDT Enable Bit0xC08A/0xC0AA Timer n Register R/WGeneral USB Registers USB Registers Register Name Address SIE1/SIE2Resistors Function Select Enable Mode Select BitPort a Resistors Enable Bit USB Data Line Pull-up and Pull-down Resistors Mode Port nArm Enable Bit Preamble Enable BitSync Enable Bit ISO Enable BitHost 1 Count Register 0xC084 Host 2 Count Register 0xC0A4 Host n Address Register R/WHost n Count Register R/W NAK Flag Bit Error Flag BitUnderflow Flag Bit Stall Flag BitPID Select ACK Flag BitHost n PID Register W PID Select DefinitionHost n Device Address Register W Host n Count Result Register RPort a Wake Interrupt Enable Bit Vbus Interrupt Enable BitID Interrupt Enable Bit SOF/EOP Interrupt Enable BitPort a Wake Interrupt Flag Bit Vbus Interrupt Flag BitID Interrupt Flag Bit SOF/EOP Interrupt Flag BitHost n SOF/EOP Counter Register R Host n SOF/EOP Count Register R/WCount Bits Count field sets the SOF/EOP counter duration Register Name Address Device 1/Device Host n Frame Register RUSB Device Only Registers Reserved USB Device Only RegistersEnable Bit IN/OUT Ignore Enable BitStall Enable Bit NAK Interrupt Enable BitDevice n Endpoint n Count Register R/W Device n Endpoint n Address Register R/WOUT Exception Flag Bit Device n Endpoint n Status Register R/WException Flag Bit Setup Flag BitTimeout occurred Timeout condition did not occur Error occurred Error did not occurDevice n Endpoint n Count Result Register Device n Endpoint n Count Result Register R/WEP7 Interrupt Enable Bit Device n Interrupt Enable Register R/WSOF/EOP Timeout Interrupt Enable Bit Reset Interrupt Enable BitEP1 Interrupt Enable Bit EP5 Interrupt Enable Bit EP2 Interrupt Enable BitEP4 Interrupt Enable Bit EP3 Interrupt Enable BitDevice n Status Register R/W Device n Address Register WEP5 Interrupt Flag Bit Reset Interrupt Flag BitEP7 Interrupt Flag Bit EP6 Interrupt Flag BitDevice n SOF/EOP Count Register W SOF/EOP Timeout Flag BitSOF/EOP Timeout Interrupt Counter Bits Device n Frame Number Register RVbus Discharge Enable Bit Vbus Pull-up Enable BitReceive Disable Bit Charge Pump Enable BitVbus Valid Flag Bit Write Protect Enable BitSAS Enable Bit Mode Select Definition Gpio Configuration 108 111 ReservedInterrupt 0 Polarity Select Bit HSS Enable BitSPI Enable Bit Interrupt 0 Enable BitGpio 0 Direction Register 0xC022 R/W Gpio 0 Input Data Register 0xC020 RGpio 1 Input Data Register 0xC026 R HSS Registers Register Name Address Gpio 1 Direction Register 0xC028 R/WHSS Registers RTS Polarity Select Bit Xoff Enable BitCTS Enable Bit Receive Interrupt Enable BitReceive Packet Ready Flag Bit Packet Mode Select BitTransmit Ready Bit Receive Overflow Flag BitHSS Data Register 0xC076 R/W HSS Transmit Gap Register 0xC074 R/WTransmit Gap Select Bits HSS Receive Counter Register 0xC07A R/W HSS Receive Address Register 0xC078 R/WHPI Registers Register Name Address HSS Transmit Address Register 0xC07C R/WHSS Transmit Counter Register 0xC07E R/W HPI RegistersHPI Breakpoint Register 0x0140 R Vbus to HPI Enable BitID to HPI Enable Bit SOF/EOP2 to HPI Enable BitReset2 to HPI Enable Bit SOF/EOP2 to CPU Enable BitSOF/EOP1 to HPI Enable Bit SOF/EOP1 to CPU Enable BitHPI Mailbox Register 0xC0C6 R/W SIEXmsg Register WSIE1msg Register SIE2msg Register Data BitsSOF/EOP2 Flag Bit Reset2 Flag BitVbus Flag Bit ID Flag BitSPI Registers Register Name Address SPI Registers Reset1 Flag BitDone1 Flag Bit Mailbox Out Flag BitMaster Enable Bit 3Wire Enable BitPhase Select Bit Master Active Enable BitFifo Init Bit Byte Mode BitRead Enable Bit SCK Strobe BitReceive Bit Length Bits Transmit Interrupt Enable BitTransfer Interrupt Enable Bit Fifo Error Flag BitTransmit Interrupt Clear Bit CRC Mode Definition CRCMode CRC PolynomialTransmit Interrupt Flag Bit Transfer Interrupt Flag BitOne in CRC Bit CRC Enable BitCRC Clear Bit Receive CRC BitSPI Transmit Count Register 0xC0DA R/W SPI Transmit Address Register 0xC0D8 R/WUart Registers Register Name Address SPI Receive Address Register 0xC0DC R/WSPI Receive Count Register 0xC0DE R/W Uart RegistersUart Baud Select Definition Baud Rate DIV8 = Uart Enable BitScale Select Bit Baud Select BitsUart Data Register 0xC0E4 R/W Transmit Full BitPin Descriptions Name Type Pin DiagramPin Descriptions A0 HPI A0 GPIO20 General Purpose IOA1 HPI A1 GPIO19 General Purpose IOCrystal Requirements XTALIN, Xtalout Booster Power Input 2.7V toAbsolute Maximum Ratings Operating ConditionsDC Characteristics Reset Timing AC Timing CharacteristicsParameter Description Min Typical Max Unit Clock TimingI2C Eeprom Timing HPI Host Port Interface Write Cycle Timing Read Cycle Time Document # 38-08014 Rev. *G Data Access Time, from HPInRD fallingHPI Host Port Interface Read Cycle Timing Read Pulse WidthHSS Byte and Block Mode Receive HSS Byte Mode TransmitHSS Block Mode Transmit Hssrts Hsscts Hardware CTS/RTS HandshakeRegister Summary Register SummaryGPIO31 GPIO30 GPIO29 SE0 SOF/EOP2 Ball 7.00 mm x 7.00 mm x 1.2 mm Fbga BA48 Package DiagramOrdering Information Ordering Information Ordering Code Package Type PB-FreeDocument History Issue Orig. Description of Change Date