Toshiba R-TH10, B-492L owner manual Printer Setup, Precautions

Page 12

2. PRINTER SETUP

EO1-33032

2.1 Precautions

2. PRINTER SETUP

2.1 Precautions

This section outlines the steps necessary to setup your B-492L/R printer prior to its operation. The section includes precautions, connecting cables, assembling accessories, loading media and ribbon, inserting an optional memory card, and performing a test print.

∙To insure the best operating environment, and to assure the safety of the operator and the equipment, please observe the following precautions.

∙Operate the printer on a stable, level, operating surface in a location free from excessive humidity, high temperature, dust, vibration or direct sunlight.

∙Keep your work environment static free. Static discharges can cause damage to delicate internal components.

∙Make sure that the printer is connected to a clean source of AC Power and that no other high voltage devices that may cause line noise interference are connected to the same mains.

∙Ensure that the printer is connected only to AC mains that has a proper ground (earth) connection.

∙Only use the power cable provided with this unit to power it..

∙Do not operate the printer with the cover open. Be careful not to allow fingers or articles of clothing to get caught into any of the moving parts of the printer.

∙Make sure to turn off the printer power and to remove the power cord from the printer whenever working on the inside of the printer or when cleaning the printer.

∙For best results, and longer printer life, use only TOSHIBA TEC recommended media and ribbons.

∙Store the media and ribbons in accordance with their specifications.

∙This printer mechanism contains high voltage components; therefore you should never remove any of the covers of the machine as you may receive an electrical shock. Additionally, the printer contains many delicate components that may be damaged if accessed by unauthorized personnel.

∙Clean the outside of the printer with a clean dry cloth or a clean cloth slightly dampened with a mild detergent solution.

∙Use caution when cleaning the thermal print head as it may become very hot while printing. Wait until it has had time to cool before cleaning. Use only the TOSHIBA TEC recommended print head cleaner to clean the print head.

∙Do not turn off the printer power or remove the power plug while the printer is printing or while the ON LINE lamp is blinking.

2- 1

Page 11 Page 13
Image 12
Page 11 Page 13
Contents 492L/R-TH10 Series For QP CE Compliance for EU only For QQWkhsoxj Precautions Request Regarding MaintenanceTable of Contents Appendix 2 Messages and LED Introduction Features AccessoriesProduct Overview UnpackingDimensions Appearance of the PrinterType Front View Type Side ViewInterior Operation PanelType Appearance of the Power Supply Unit Printer Setup PrecautionsProcedure before Operation Connecting the Cables to Your Printer Connecting the Power Cord Turning the Printer Turning on the PrinterTurning OFF the Printer Causing injury Loading the MediaPaper Holder Media Guide Setting the feed gap sensor position Setting the black mark sensor positionBatch mode Strip modeLoading the Media Loading the Ribbon Pcmcia Cards Test Print Inserting the Optional Pcmcia CardsOn Line Mode Operation PanelOperation To be printedMaintenance CleaningPrint Head/Platen Media Guide Plate/ Pinch Roller/Sensors Pinch Roller Feed Roller Paper Guide B Locking Screw Paper Holder Covers and PanelsCare/Handling of the Media and Ribbon Troubleshooting Error MessagesError Messages Problems/Causes Solutions Restart keyPossible Problems Error Messages Problems/Cause SolutionsPossible Problems Causes Solutions Threshold Setting Removing Jammed MediaThreshold Setting Overview Installing the Printer Drivers Printer OperationDriver Installation System RequirementsSystem InterfaceCont Change to the Software License Agreement screenDriver Installation Driver files copy will start Uninstalling the TEC B-492 Printer Driver Uninstalling the TEC B-492 Printer Driver Appendix 1 Specifications A1.1 PrinterModel 492L/R-TH10-QQ 492L/R-TH10-QP A1.2 Options A1.3 MediaA1.3.1 Media Type Option Name Type Description SourceA1.3.2 Detection Area of the Transmissive Sensor A1.3.3 Detection Area of the Reflective Sensor A1.3.4 Effective Print AreaA1.4 Ribbon Symbols in the message Appendix 2 Messages and Leds53&$ Appendix 3 Interface „Interface CablesAppendix 4 System Mode A4.1 Operation PanelA4.2 Overview 2PARAMETER SET 5SENSOR ADJ RAM Clear 7IP AddressA4.3 Reset Mode A4.4 Self-Diagnostic TestA4.4 Self-Diagnostic Maintenance counter/parameter settings print outTest Ribbon type selectionPrint head element check 2PAUSE63 567 Feed keyFine Adjustment Strip Position Fine AdjustmentA4.5 Printer Parameter ContBack Feed Length Fine Adjustment $&.$-PPA4.5 Printer Parameter X Axis Fine Adjustment Cont Feed $-867PPPrint Thermal Transfer PrintThermal Direct Print Ribbon Motor Voltage Fine Adjustment Feed/Rewind Motor 1Rewind$-!Motor 5%1Feed$-Motor%Threshold Manual Fine Adjustment Black Mark/Feed Gap Sensor Black Mark SensorPrint Condition Setting A4.6 Test PrintTest Print menu contains the following SelectionIssue Count Setting Specifying the Print Condition for the Test PrintPrint Speed Setting Sensor Type SelectionRibbon Type Selection Issue Mode Selection Label Length SettingTest Print Pattern Selection Pause keySlant Line 1 dot Slant Line 3 dotsBarcode Non-PrintingFactory Test A4.7 Dump Mode Auto Print $87235,17 755/$1A4.8.1 Self-Diagnostic Test Result Sample and Descriptions A4.8 Additional InformationSdram 8MB Print Head Resistance Rank Table EXP.I/OTotal Feed ∙ Descriptions of the Maintenance Counter XON+READY Auto A4.8.3 Magnified Views of Slant Line Pattern BusyAppendix 5 Print Samples CODE39 Full Ascii UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digitsUPC-A+2 digits UPC-A+5 digits KIX Code MaxiCodeGlossaries Pre-printed label Index Index
Top Page Image Contents