Toshiba B-492L, R-TH10 owner manual A4.3 Reset Mode, A4.4 Self-Diagnostic Test

Page 53
Select the ribbon type
Print out the Maintenance Counter and Parameter Settings.
Perform a Self-Diagnostic Test, and prints out the result.
Check to see if there is any problem with the print head.

APPENDIX 4 SYSTEM MODE

EO1-33032

A4.3 Reset Mode

A4.3 Reset Mode

NOTE:

If the [RESTART] key is held for less than 3 seconds when the printer is in an error or pause state, the printer will restart printing. However, when a communication error or command error occurs, the printer will return to an idle condition.

A4.4 Self-Diagnostic Test

Outline of Self-Diagnostic Test

In the Self-Diagnostic Test mode, the printer checks and prints out the printer system information such as the sensor or interface, and the Maintenance Counter. It also performs the print head broken element check.

NOTE:

Use the [FEED] or [RESTART]

key to select a desired option.

The Reset operation clears all the print data that has been sent to the printer from the computer, and returns the printer to an idle condition.

1. The321printer$86(/,1(is on, standing￿￿by, or printing.

2. To ￿￿stop!5(6(7printing, or clear the data sent from the computer, press the [PAUSE] key. The printer stops printing.

3. Press21and/,1(hold the [RSTART] key for 3 seconds or longer.

4. Press [PAUSE] key. All data that has been received sent from the computer￿￿!',will$*￿be 9[cleared,￿[and the printer returns to an idle condition.

The Self5,%%21-Diagnostic75$16Test￿contains the following sub menus:

0$$872,17(1[PAUSE]',$$*11267,&(&217&￿

[PAUSE]

+([FEED]$'&+(&.[RESTART]

[FEED] [RESTART]

[FEED] [RESTART]

A4- 3

Image 53
Contents 492L/R-TH10 Series For QQ For QP CE Compliance for EU onlyWkhsoxj Request Regarding Maintenance PrecautionsTable of Contents Appendix 2 Messages and LED Accessories Introduction FeaturesProduct Overview UnpackingType DimensionsAppearance of the Printer Type Side View Front ViewType InteriorOperation Panel Appearance of the Power Supply Unit Precautions Printer SetupProcedure before Operation Connecting the Cables to Your Printer Connecting the Power Cord Turning OFF the Printer Turning the PrinterTurning on the Printer Loading the Media Causing injuryPaper Holder Media Guide Setting the black mark sensor position Setting the feed gap sensor positionStrip mode Batch modeLoading the Media Loading the Ribbon Pcmcia Cards Inserting the Optional Pcmcia Cards Test PrintOperation Panel On Line ModeTo be printed OperationPrint Head/Platen MaintenanceCleaning Media Guide Plate/ Pinch Roller/Sensors Pinch Roller Feed Roller Paper Guide B Locking Screw Covers and Panels Paper HolderCare/Handling of the Media and Ribbon Error Messages TroubleshootingError Messages Problems/Causes Solutions Restart keyPossible Problems Causes Solutions Possible ProblemsError Messages Problems/Cause Solutions Removing Jammed Media Threshold SettingThreshold Setting Printer Operation Overview Installing the Printer DriversSystem Requirements Driver InstallationSystem InterfaceChange to the Software License Agreement screen ContDriver Installation Driver files copy will start Uninstalling the TEC B-492 Printer Driver Uninstalling the TEC B-492 Printer Driver Model 492L/R-TH10-QQ 492L/R-TH10-QP Appendix 1 SpecificationsA1.1 Printer A1.3 Media A1.2 OptionsA1.3.1 Media Type Option Name Type Description SourceA1.3.2 Detection Area of the Transmissive Sensor A1.3.4 Effective Print Area A1.3.3 Detection Area of the Reflective SensorA1.4 Ribbon Appendix 2 Messages and Leds Symbols in the message53&$ „Interface Cables Appendix 3 InterfaceA4.1 Operation Panel Appendix 4 System Mode2PARAMETER SET 5SENSOR ADJ RAM Clear 7IP Address A4.2 OverviewA4.4 Self-Diagnostic Test A4.3 Reset ModeMaintenance counter/parameter settings print out A4.4 Self-DiagnosticTest Ribbon type selectionPrint head element check 2PAUSE63 Feed key 567Strip Position Fine Adjustment Fine AdjustmentA4.5 Printer Parameter Cont$&.$-PP Back Feed Length Fine AdjustmentFeed $-867PP A4.5 Printer Parameter X Axis Fine Adjustment ContThermal Direct Print PrintThermal Transfer Print 1Rewind$-!Motor 5%1Feed$-Motor% Ribbon Motor Voltage Fine Adjustment Feed/Rewind MotorBlack Mark Sensor Threshold Manual Fine Adjustment Black Mark/Feed Gap SensorA4.6 Test Print Print Condition SettingTest Print menu contains the following SelectionSpecifying the Print Condition for the Test Print Issue Count SettingRibbon Type Selection Print Speed SettingSensor Type Selection Label Length Setting Issue Mode SelectionPause key Test Print Pattern SelectionSlant Line 1 dot Slant Line 3 dotsFactory Test BarcodeNon-Printing Auto Print $87235,17 755/$1 A4.7 Dump ModeA4.8 Additional Information A4.8.1 Self-Diagnostic Test Result Sample and DescriptionsSdram 8MB EXP.I/O Print Head Resistance Rank TableTotal Feed ∙ Descriptions of the Maintenance Counter XON+READY Auto Busy A4.8.3 Magnified Views of Slant Line PatternAppendix 5 Print Samples UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digits CODE39 Full AsciiKIX Code MaxiCode UPC-A+2 digits UPC-A+5 digitsGlossaries Pre-printed label Index Index