Toshiba R-TH10, B-492L owner manual Connecting the Cables to Your Printer, Type

Page 14

2. PRINTER SETUP

EO1-33032

2.4 Connecting the Cables to Your Printer

2.4Connecting the Cables to Your Printer

The following paragraphs outlines how to connect the cables from the B- 492L/R printer to your host computer, and will also show how to make cable connections to other devices such as the KB-80-QM keyboard, etc. Depending on the application software you use to print labels, there are two possibilities for connecting the printer to your host computer. These are:

∙A serial cable connection between the printer’s RS-232 serial connector and one of your host computer’s COM ports (Refer to APPENDIX 3.)

∙A parallel cable connection between the printer’s standard parallel connector and your host computer’s parallel port (LPT).

∙An Ethernet connection using the optional PCMCIA interface board and LAN card (Refer to section 2.9)

The diagram below shows all the possible cable connections to the current version of the B-492L/R printer.

e

dc

c	f	f d
c
		e

[L Type]

[R Type]

cParallel Interface Connector (Centronics)

dSerial Interface Connector (RS-232C)

eKB-80-QM Keyboard Interface Connector (Option)

fExpansion I/O Interface Connector

2- 3

Image 14

Contents 492L/R-TH10 Series For QP CE Compliance for EU only For QQWkhsoxj Precautions Request Regarding MaintenanceTable of Contents Appendix 2 Messages and LED Product Overview Introduction FeaturesAccessories UnpackingType DimensionsAppearance of the Printer Front View Type Side ViewType InteriorOperation Panel Appearance of the Power Supply Unit Printer Setup PrecautionsProcedure before Operation Connecting the Cables to Your Printer Connecting the Power Cord Turning OFF the Printer Turning the PrinterTurning on the Printer Causing injury Loading the MediaPaper Holder Media Guide Setting the feed gap sensor position Setting the black mark sensor positionBatch mode Strip modeLoading the Media Loading the Ribbon Pcmcia Cards Test Print Inserting the Optional Pcmcia CardsOn Line Mode Operation PanelOperation To be printedPrint Head/Platen MaintenanceCleaning Media Guide Plate/ Pinch Roller/Sensors Pinch Roller Feed Roller Paper Guide B Locking Screw Paper Holder Covers and PanelsCare/Handling of the Media and Ribbon Error Messages Problems/Causes Solutions TroubleshootingError Messages Restart keyPossible Problems Causes Solutions Possible ProblemsError Messages Problems/Cause Solutions Threshold Setting Removing Jammed MediaThreshold Setting Overview Installing the Printer Drivers Printer OperationSystem Driver InstallationSystem Requirements InterfaceCont Change to the Software License Agreement screenDriver Installation Driver files copy will start Uninstalling the TEC B-492 Printer Driver Uninstalling the TEC B-492 Printer Driver Model 492L/R-TH10-QQ 492L/R-TH10-QP Appendix 1 SpecificationsA1.1 Printer A1.3.1 Media Type A1.2 OptionsA1.3 Media Option Name Type Description SourceA1.3.2 Detection Area of the Transmissive Sensor A1.3.3 Detection Area of the Reflective Sensor A1.3.4 Effective Print AreaA1.4 Ribbon Symbols in the message Appendix 2 Messages and Leds53&$ Appendix 3 Interface „Interface CablesAppendix 4 System Mode A4.1 Operation PanelA4.2 Overview 2PARAMETER SET 5SENSOR ADJ RAM Clear 7IP AddressA4.3 Reset Mode A4.4 Self-Diagnostic TestTest A4.4 Self-DiagnosticMaintenance counter/parameter settings print out Ribbon type selectionPrint head element check 2PAUSE63 567 Feed keyA4.5 Printer Parameter Fine AdjustmentStrip Position Fine Adjustment ContBack Feed Length Fine Adjustment $&.$-PPA4.5 Printer Parameter X Axis Fine Adjustment Cont Feed $-867PPThermal Direct Print PrintThermal Transfer Print Ribbon Motor Voltage Fine Adjustment Feed/Rewind Motor 1Rewind$-!Motor 5%1Feed$-Motor%Threshold Manual Fine Adjustment Black Mark/Feed Gap Sensor Black Mark SensorTest Print menu contains the following Print Condition SettingA4.6 Test Print SelectionIssue Count Setting Specifying the Print Condition for the Test PrintRibbon Type Selection Print Speed SettingSensor Type Selection Issue Mode Selection Label Length SettingSlant Line 1 dot Test Print Pattern SelectionPause key Slant Line 3 dotsFactory Test BarcodeNon-Printing A4.7 Dump Mode Auto Print $87235,17 755/$1A4.8.1 Self-Diagnostic Test Result Sample and Descriptions A4.8 Additional InformationSdram 8MB Print Head Resistance Rank Table EXP.I/OTotal Feed ∙ Descriptions of the Maintenance Counter XON+READY Auto A4.8.3 Magnified Views of Slant Line Pattern BusyAppendix 5 Print Samples CODE39 Full Ascii UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digitsUPC-A+2 digits UPC-A+5 digits KIX Code MaxiCodeGlossaries Pre-printed label Index Index