Toshiba R-TH10, B-492L Turning the Printer, Turning on the Printer, Turning OFF the Printer

Page 16

2. PRINTER SETUP

EO1-33032

2.6 Turning the Printer ON/OFF

2.6Turning the Printer

ON/OFF

2.6.1 Turning ON the Printer

CAUTION!

Use the power switch to turn the printer On/Off. Plugging or unplugging the power cord to turn the printer On/Off may cause fire, an electric shock, or damage to the printer.

When the printer is connected to a host computer it is good practice to turn the printer ON before turning on the host computer and to turn OFF the host computer before turning off the printer.

1.To turn ON the printer power, press the power switch as shown in the diagram below. Note that ( ) is the power ON side of the switch.

Power Switch

NOTE:

If a message other than ON LINE appears on the display or the ERROR LED lamp is illuminated, go to Chapter 5.1, Error Messages.

2.Check that the message ON LINE appears on the LCD Display and that the ON LINE and POWER LED lights are illuminated

2.6.2Turning OFF the Printer

CAUTION!

1.Do not turn off the printer power while the media is being printed as this may cause a paper jam or damage to the printer.

2.Do not turn off the printer power while the ON LINE light is blinking as this may cause damage to your host computer.

1.Before turning off the printer power switch verify that the ON LINE message is on the LCD Message Display and that the ON LINE LED light is on and not flashing.

2.To turn OFF the printer power press the power switch as shown in the diagram below. Note that ( {) is the power OFF side of the switch.

Power Switch

2- 5

Image 16

Contents 492L/R-TH10 Series For QP CE Compliance for EU only For QQWkhsoxj Precautions Request Regarding MaintenanceTable of Contents Appendix 2 Messages and LED Introduction Features AccessoriesProduct Overview UnpackingAppearance of the Printer DimensionsType Front View Type Side ViewOperation Panel InteriorType Appearance of the Power Supply Unit Printer Setup PrecautionsProcedure before Operation Connecting the Cables to Your Printer Connecting the Power Cord Turning on the Printer Turning the PrinterTurning OFF the Printer Causing injury Loading the MediaPaper Holder Media Guide Setting the feed gap sensor position Setting the black mark sensor positionBatch mode Strip modeLoading the Media Loading the Ribbon Pcmcia Cards Test Print Inserting the Optional Pcmcia CardsOn Line Mode Operation PanelOperation To be printedCleaning MaintenancePrint Head/Platen Media Guide Plate/ Pinch Roller/Sensors Pinch Roller Feed Roller Paper Guide B Locking Screw Paper Holder Covers and PanelsCare/Handling of the Media and Ribbon Troubleshooting Error MessagesError Messages Problems/Causes Solutions Restart keyError Messages Problems/Cause Solutions Possible ProblemsPossible Problems Causes Solutions Threshold Setting Removing Jammed MediaThreshold Setting Overview Installing the Printer Drivers Printer OperationDriver Installation System RequirementsSystem InterfaceCont Change to the Software License Agreement screenDriver Installation Driver files copy will start Uninstalling the TEC B-492 Printer Driver Uninstalling the TEC B-492 Printer Driver A1.1 Printer Appendix 1 SpecificationsModel 492L/R-TH10-QQ 492L/R-TH10-QP A1.2 Options A1.3 MediaA1.3.1 Media Type Option Name Type Description SourceA1.3.2 Detection Area of the Transmissive Sensor A1.3.3 Detection Area of the Reflective Sensor A1.3.4 Effective Print AreaA1.4 Ribbon Symbols in the message Appendix 2 Messages and Leds53&$ Appendix 3 Interface „Interface CablesAppendix 4 System Mode A4.1 Operation PanelA4.2 Overview 2PARAMETER SET 5SENSOR ADJ RAM Clear 7IP AddressA4.3 Reset Mode A4.4 Self-Diagnostic TestA4.4 Self-Diagnostic Maintenance counter/parameter settings print outTest Ribbon type selectionPrint head element check 2PAUSE63 567 Feed keyFine Adjustment Strip Position Fine AdjustmentA4.5 Printer Parameter ContBack Feed Length Fine Adjustment $&.$-PPA4.5 Printer Parameter X Axis Fine Adjustment Cont Feed $-867PPThermal Transfer Print PrintThermal Direct Print Ribbon Motor Voltage Fine Adjustment Feed/Rewind Motor 1Rewind$-!Motor 5%1Feed$-Motor%Threshold Manual Fine Adjustment Black Mark/Feed Gap Sensor Black Mark SensorPrint Condition Setting A4.6 Test PrintTest Print menu contains the following SelectionIssue Count Setting Specifying the Print Condition for the Test PrintSensor Type Selection Print Speed SettingRibbon Type Selection Issue Mode Selection Label Length SettingTest Print Pattern Selection Pause keySlant Line 1 dot Slant Line 3 dotsNon-Printing BarcodeFactory Test A4.7 Dump Mode Auto Print $87235,17 755/$1A4.8.1 Self-Diagnostic Test Result Sample and Descriptions A4.8 Additional InformationSdram 8MB Print Head Resistance Rank Table EXP.I/OTotal Feed ∙ Descriptions of the Maintenance Counter XON+READY Auto A4.8.3 Magnified Views of Slant Line Pattern BusyAppendix 5 Print Samples CODE39 Full Ascii UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digitsUPC-A+2 digits UPC-A+5 digits KIX Code MaxiCodeGlossaries Pre-printed label Index Index