Toshiba R-TH10 A1.2 Options, A1.3 Media, A1.3.1 Media Type, Option Name Type Description Source

Page 44

APPENDIX 1 SPECIFICATIONS	EO1-33032
	A1.2 Options

A1.2 Options

Option Name	Type	Description	Source
Keyboard module	KB-80-QM	This module is an external intelligent keyboard unit,	See NOTE.
		including a 16 digit by 2 line LCD and 28 key
		switches.
PCMCIA interface	B-7708-PC-QM	This board enables the use of the following	See NOTE.
board		PCMCIA cards:
		LAN card: 3 COM EtherLink® III (recommended)
		ATA card: Conforming to PC card ATA standard
		Flash memory card: 4MB card (See page 2-13.)

NOTE:

Available from your nearest TOSHIBA TEC representative or TOSHIBA TEC Head Quarters.

A1.3 Media

Please make sure that the media to be used is approved by TOSHIBA TEC. The warranties do not apply to problems caused by using media that is not approved by TOSHIBA TEC.

For information regarding TOSHIBA TEC-approved media, please contact a TOSHIBA TEC authorized service representative.

A1.3.1 Media Type

This thermal transfer/direct thermal printer is specifically designed for label media. The table below shows the size and shape of the media available for this printer.

Black Mark

(on reverse side) Refer to

D

NOTE 3 below.

Stop position

C

BA

?	Feed Direction

A1- 2

Image 44

Contents 492L/R-TH10 Series For QP CE Compliance for EU only For QQWkhsoxj Precautions Request Regarding MaintenanceTable of Contents Appendix 2 Messages and LED Introduction Features AccessoriesProduct Overview UnpackingType DimensionsAppearance of the Printer Front View Type Side ViewType InteriorOperation Panel Appearance of the Power Supply Unit Printer Setup PrecautionsProcedure before Operation Connecting the Cables to Your Printer Connecting the Power Cord Turning OFF the Printer Turning the PrinterTurning on the Printer Causing injury Loading the MediaPaper Holder Media Guide Setting the feed gap sensor position Setting the black mark sensor positionBatch mode Strip modeLoading the Media Loading the Ribbon Pcmcia Cards Test Print Inserting the Optional Pcmcia CardsOn Line Mode Operation PanelOperation To be printedPrint Head/Platen MaintenanceCleaning Media Guide Plate/ Pinch Roller/Sensors Pinch Roller Feed Roller Paper Guide B Locking Screw Paper Holder Covers and PanelsCare/Handling of the Media and Ribbon Troubleshooting Error MessagesError Messages Problems/Causes Solutions Restart keyPossible Problems Causes Solutions Possible ProblemsError Messages Problems/Cause Solutions Threshold Setting Removing Jammed MediaThreshold Setting Overview Installing the Printer Drivers Printer OperationDriver Installation System RequirementsSystem InterfaceCont Change to the Software License Agreement screenDriver Installation Driver files copy will start Uninstalling the TEC B-492 Printer Driver Uninstalling the TEC B-492 Printer Driver Model 492L/R-TH10-QQ 492L/R-TH10-QP Appendix 1 SpecificationsA1.1 Printer A1.2 Options A1.3 MediaA1.3.1 Media Type Option Name Type Description SourceA1.3.2 Detection Area of the Transmissive Sensor A1.3.3 Detection Area of the Reflective Sensor A1.3.4 Effective Print AreaA1.4 Ribbon Symbols in the message Appendix 2 Messages and Leds53&$ Appendix 3 Interface „Interface CablesAppendix 4 System Mode A4.1 Operation PanelA4.2 Overview 2PARAMETER SET 5SENSOR ADJ RAM Clear 7IP AddressA4.3 Reset Mode A4.4 Self-Diagnostic TestA4.4 Self-Diagnostic Maintenance counter/parameter settings print outTest Ribbon type selectionPrint head element check 2PAUSE63 567 Feed keyFine Adjustment Strip Position Fine AdjustmentA4.5 Printer Parameter ContBack Feed Length Fine Adjustment $&.$-PPA4.5 Printer Parameter X Axis Fine Adjustment Cont Feed $-867PPThermal Direct Print PrintThermal Transfer Print Ribbon Motor Voltage Fine Adjustment Feed/Rewind Motor 1Rewind$-!Motor 5%1Feed$-Motor%Threshold Manual Fine Adjustment Black Mark/Feed Gap Sensor Black Mark SensorPrint Condition Setting A4.6 Test PrintTest Print menu contains the following SelectionIssue Count Setting Specifying the Print Condition for the Test PrintRibbon Type Selection Print Speed SettingSensor Type Selection Issue Mode Selection Label Length SettingTest Print Pattern Selection Pause keySlant Line 1 dot Slant Line 3 dotsFactory Test BarcodeNon-Printing A4.7 Dump Mode Auto Print $87235,17 755/$1A4.8.1 Self-Diagnostic Test Result Sample and Descriptions A4.8 Additional InformationSdram 8MB Print Head Resistance Rank Table EXP.I/OTotal Feed ∙ Descriptions of the Maintenance Counter XON+READY Auto A4.8.3 Magnified Views of Slant Line Pattern BusyAppendix 5 Print Samples CODE39 Full Ascii UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digitsUPC-A+2 digits UPC-A+5 digits KIX Code MaxiCodeGlossaries Pre-printed label Index Index