Toshiba B-492L, R-TH10 owner manual On Line Mode, Operation Panel

Page 25

3. ON LINE MODE

EO1-33032

3.1 Operation Panel

3. ON LINE MODE

3.1 Operation Panel

This chapter describes usage of the keys on the Operation Panel in On Line Mode.

When the printer is in On Line Mode and connected to a host computer, the normal operation of printing images on labels can be achieved.

The figure below shows the Operation Panel and key functions..

LCD Message Display

POWER LED (Green)

[RESTART] key

[FEED] key

POWER ON LINE ERROR

FEED RESTART PAUSE

ON LINE LED (Green)

ERROR LED (Red)

[PAUSE] key

NOTE:

Use the [RESTART] key to resume printing after a pause, or after clearing an error.

The LCD Message Display shows messages to indicate the printer’s current status. Up to 16 characters can be displayed on this line.

There are three LED lights on the Operation Panel.

LED	Illuminates when…	Flashes when…
POWER	The printer is turned on.	-----
ON LINE	The printer is ready to	The printer is
	print.	communicating with
		your computer.
ERROR	Any error occurs on the	-----
	printer.	-----
	printer.

There are three keys on the Operation Panel.

PAUSE	Used to stop printing temporarily.
RESTART	Used to restart printing.
FEED	Used to feed the media.

3- 1

Image 25

Contents 492L/R-TH10 Series For QQ For QP CE Compliance for EU onlyWkhsoxj Request Regarding Maintenance PrecautionsTable of Contents Appendix 2 Messages and LED Accessories Introduction FeaturesProduct Overview UnpackingAppearance of the Printer DimensionsType Type Side View Front ViewOperation Panel InteriorType Appearance of the Power Supply Unit Precautions Printer SetupProcedure before Operation Connecting the Cables to Your Printer Connecting the Power Cord Turning on the Printer Turning the PrinterTurning OFF the Printer Loading the Media Causing injuryPaper Holder Media Guide Setting the black mark sensor position Setting the feed gap sensor positionStrip mode Batch modeLoading the Media Loading the Ribbon Pcmcia Cards Inserting the Optional Pcmcia Cards Test PrintOperation Panel On Line ModeTo be printed OperationCleaning MaintenancePrint Head/Platen Media Guide Plate/ Pinch Roller/Sensors Pinch Roller Feed Roller Paper Guide B Locking Screw Covers and Panels Paper HolderCare/Handling of the Media and Ribbon Error Messages TroubleshootingError Messages Problems/Causes Solutions Restart keyError Messages Problems/Cause Solutions Possible ProblemsPossible Problems Causes Solutions Removing Jammed Media Threshold SettingThreshold Setting Printer Operation Overview Installing the Printer DriversSystem Requirements Driver InstallationSystem InterfaceChange to the Software License Agreement screen ContDriver Installation Driver files copy will start Uninstalling the TEC B-492 Printer Driver Uninstalling the TEC B-492 Printer Driver A1.1 Printer Appendix 1 SpecificationsModel 492L/R-TH10-QQ 492L/R-TH10-QP A1.3 Media A1.2 OptionsA1.3.1 Media Type Option Name Type Description SourceA1.3.2 Detection Area of the Transmissive Sensor A1.3.4 Effective Print Area A1.3.3 Detection Area of the Reflective SensorA1.4 Ribbon Appendix 2 Messages and Leds Symbols in the message53&$ „Interface Cables Appendix 3 InterfaceA4.1 Operation Panel Appendix 4 System Mode2PARAMETER SET 5SENSOR ADJ RAM Clear 7IP Address A4.2 OverviewA4.4 Self-Diagnostic Test A4.3 Reset ModeMaintenance counter/parameter settings print out A4.4 Self-DiagnosticTest Ribbon type selectionPrint head element check 2PAUSE63 Feed key 567Strip Position Fine Adjustment Fine AdjustmentA4.5 Printer Parameter Cont$&.$-PP Back Feed Length Fine AdjustmentFeed $-867PP A4.5 Printer Parameter X Axis Fine Adjustment ContThermal Transfer Print PrintThermal Direct Print 1Rewind$-!Motor 5%1Feed$-Motor% Ribbon Motor Voltage Fine Adjustment Feed/Rewind MotorBlack Mark Sensor Threshold Manual Fine Adjustment Black Mark/Feed Gap SensorA4.6 Test Print Print Condition SettingTest Print menu contains the following SelectionSpecifying the Print Condition for the Test Print Issue Count SettingSensor Type Selection Print Speed SettingRibbon Type Selection Label Length Setting Issue Mode SelectionPause key Test Print Pattern SelectionSlant Line 1 dot Slant Line 3 dotsNon-Printing BarcodeFactory Test Auto Print $87235,17 755/$1 A4.7 Dump ModeA4.8 Additional Information A4.8.1 Self-Diagnostic Test Result Sample and DescriptionsSdram 8MB EXP.I/O Print Head Resistance Rank TableTotal Feed ∙ Descriptions of the Maintenance Counter XON+READY Auto Busy A4.8.3 Magnified Views of Slant Line PatternAppendix 5 Print Samples UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digits CODE39 Full AsciiKIX Code MaxiCode UPC-A+2 digits UPC-A+5 digitsGlossaries Pre-printed label Index Index