Toshiba R-TH10, B-492L owner manual Pre-printed label

Page 82

GLOSSARIES

EO1-33032

GLOSSARIES

Pre-printed label

A type of label on which characters, logos, and other designs have been already printed.

Printing speed

The speed at which printing occurs. This speed is expressed in units of IPS (inches per second).

Reflective sensor

See Black mark sensor.

Resolution

The degree of detail to which an image can be duplicated. The minimum unit of divided image is called a pixel. As the resolution becomes higher, the number of pixels increases, resulting in a more detailed image.

Ribbon

An inked film used to transfer an image onto the media. In thermal transfer printing, it is heated by the thermal print head, causing an image to be transferred onto the media

Supply

Media and ribbon

Thermal direct printing

A printing method using no ribbon, but thermal media which reacts to heat. The thermal print head heats the thermal media directly, causing print image to be printed on the media.

Thermal print head

A print head using thermal transfer or thermal direct printing method..

Thermal transfer printing

A printing method that uses the thermal print head to heat an ink or resin coating on the ribbon against the media, causing the ink/resin to transfer onto the media.

Threshold setting

A sensor setting operation to help the printer maintain a constant print position on pre-printed media. .

Transmissive sensor

See Feed gap sensor.

X Axis

In the printer, it is the horizontal position (left and right) of the print on the label. This position may be adjusted by command from the host computer, or by a parameter change on the printer.

Image 82
Contents 492L/R-TH10 Series For QP CE Compliance for EU only For QQWkhsoxj Precautions Request Regarding MaintenanceTable of Contents Appendix 2 Messages and LED Product Overview Introduction FeaturesAccessories UnpackingAppearance of the Printer DimensionsType Front View Type Side ViewOperation Panel InteriorType Appearance of the Power Supply Unit Printer Setup PrecautionsProcedure before Operation Connecting the Cables to Your Printer Connecting the Power Cord Turning on the Printer Turning the PrinterTurning OFF the Printer Causing injury Loading the MediaPaper Holder Media Guide Setting the feed gap sensor position Setting the black mark sensor positionBatch mode Strip modeLoading the Media Loading the Ribbon Pcmcia Cards Test Print Inserting the Optional Pcmcia CardsOn Line Mode Operation PanelOperation To be printedCleaning MaintenancePrint Head/Platen Media Guide Plate/ Pinch Roller/Sensors Pinch Roller Feed Roller Paper Guide B Locking Screw Paper Holder Covers and PanelsCare/Handling of the Media and Ribbon Error Messages Problems/Causes Solutions TroubleshootingError Messages Restart keyError Messages Problems/Cause Solutions Possible ProblemsPossible Problems Causes Solutions Threshold Setting Removing Jammed MediaThreshold Setting Overview Installing the Printer Drivers Printer OperationSystem Driver InstallationSystem Requirements InterfaceCont Change to the Software License Agreement screenDriver Installation Driver files copy will start Uninstalling the TEC B-492 Printer Driver Uninstalling the TEC B-492 Printer Driver A1.1 Printer Appendix 1 SpecificationsModel 492L/R-TH10-QQ 492L/R-TH10-QP A1.3.1 Media Type A1.2 OptionsA1.3 Media Option Name Type Description SourceA1.3.2 Detection Area of the Transmissive Sensor A1.3.3 Detection Area of the Reflective Sensor A1.3.4 Effective Print AreaA1.4 Ribbon Symbols in the message Appendix 2 Messages and Leds53&$ Appendix 3 Interface „Interface CablesAppendix 4 System Mode A4.1 Operation PanelA4.2 Overview 2PARAMETER SET 5SENSOR ADJ RAM Clear 7IP AddressA4.3 Reset Mode A4.4 Self-Diagnostic TestTest A4.4 Self-DiagnosticMaintenance counter/parameter settings print out Ribbon type selectionPrint head element check 2PAUSE63 567 Feed keyA4.5 Printer Parameter Fine AdjustmentStrip Position Fine Adjustment ContBack Feed Length Fine Adjustment $&.$-PPA4.5 Printer Parameter X Axis Fine Adjustment Cont Feed $-867PPThermal Transfer Print PrintThermal Direct Print Ribbon Motor Voltage Fine Adjustment Feed/Rewind Motor 1Rewind$-!Motor 5%1Feed$-Motor%Threshold Manual Fine Adjustment Black Mark/Feed Gap Sensor Black Mark SensorTest Print menu contains the following Print Condition SettingA4.6 Test Print SelectionIssue Count Setting Specifying the Print Condition for the Test PrintSensor Type Selection Print Speed SettingRibbon Type Selection Issue Mode Selection Label Length SettingSlant Line 1 dot Test Print Pattern SelectionPause key Slant Line 3 dotsNon-Printing BarcodeFactory Test A4.7 Dump Mode Auto Print $87235,17 755/$1A4.8.1 Self-Diagnostic Test Result Sample and Descriptions A4.8 Additional InformationSdram 8MB Print Head Resistance Rank Table EXP.I/OTotal Feed ∙ Descriptions of the Maintenance Counter XON+READY Auto A4.8.3 Magnified Views of Slant Line Pattern BusyAppendix 5 Print Samples CODE39 Full Ascii UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digitsUPC-A+2 digits UPC-A+5 digits KIX Code MaxiCodeGlossaries Pre-printed label Index Index