Toshiba R-TH10, B-492L owner manual Loading the Ribbon

Page 22

2. PRINTER SETUP

EO1-33032

2.8 Loading the Ribbon

2.8 Loading the Ribbon

WARNING!

1.Do not touch any moving parts. To reduce the risk of fingers, jewellery, clothing, etc. being drawn into the moving parts, be sure to load the ribbon once the printer has stopped moving completely.

2.To avoid injury, be careful not to trap your fingers while opening or closing the cover.

3.Be sure to open the top cover fully, otherwise the top cover may close, causing injury.

1.Grasp the tabs on the top and bottom of the ribbon stoppers and move the ribbon stoppers back to the end of the shaft.

Ribbon Stopper

2.Leaving plenty of slack between the ribbon spools, place the ribbon onto the ribbon shafts as shown below. When the ribbon is fitted, it must be positioned in the ribbon sensor.

Ribbon Shafts

NOTE:

The ribbon sensor is mounted on the rear of the printer block to detect a ribbon end. When a ribbon end is detected, “NO RIBBON” message will appear on the display and the ERROR LED will illuminate.

Ribbon

Ribbon Sensor

2-11

Image 22

Contents 492L/R-TH10 Series For QP CE Compliance for EU only For QQWkhsoxj Precautions Request Regarding MaintenanceTable of Contents Appendix 2 Messages and LED Product Overview Introduction FeaturesAccessories UnpackingAppearance of the Printer DimensionsType Front View Type Side ViewOperation Panel InteriorType Appearance of the Power Supply Unit Printer Setup PrecautionsProcedure before Operation Connecting the Cables to Your Printer Connecting the Power Cord Turning on the Printer Turning the PrinterTurning OFF the Printer Causing injury Loading the MediaPaper Holder Media Guide Setting the feed gap sensor position Setting the black mark sensor positionBatch mode Strip modeLoading the Media Loading the Ribbon Pcmcia Cards Test Print Inserting the Optional Pcmcia CardsOn Line Mode Operation PanelOperation To be printedCleaning MaintenancePrint Head/Platen Media Guide Plate/ Pinch Roller/Sensors Pinch Roller Feed Roller Paper Guide B Locking Screw Paper Holder Covers and PanelsCare/Handling of the Media and Ribbon Error Messages Problems/Causes Solutions TroubleshootingError Messages Restart keyError Messages Problems/Cause Solutions Possible ProblemsPossible Problems Causes Solutions Threshold Setting Removing Jammed MediaThreshold Setting Overview Installing the Printer Drivers Printer OperationSystem Driver InstallationSystem Requirements InterfaceCont Change to the Software License Agreement screenDriver Installation Driver files copy will start Uninstalling the TEC B-492 Printer Driver Uninstalling the TEC B-492 Printer Driver A1.1 Printer Appendix 1 SpecificationsModel 492L/R-TH10-QQ 492L/R-TH10-QP A1.3.1 Media Type A1.2 OptionsA1.3 Media Option Name Type Description SourceA1.3.2 Detection Area of the Transmissive Sensor A1.3.3 Detection Area of the Reflective Sensor A1.3.4 Effective Print AreaA1.4 Ribbon Symbols in the message Appendix 2 Messages and Leds53&$ Appendix 3 Interface „Interface CablesAppendix 4 System Mode A4.1 Operation PanelA4.2 Overview 2PARAMETER SET 5SENSOR ADJ RAM Clear 7IP AddressA4.3 Reset Mode A4.4 Self-Diagnostic TestTest A4.4 Self-DiagnosticMaintenance counter/parameter settings print out Ribbon type selectionPrint head element check 2PAUSE63 567 Feed keyA4.5 Printer Parameter Fine AdjustmentStrip Position Fine Adjustment ContBack Feed Length Fine Adjustment $&.$-PPA4.5 Printer Parameter X Axis Fine Adjustment Cont Feed $-867PPThermal Transfer Print PrintThermal Direct Print Ribbon Motor Voltage Fine Adjustment Feed/Rewind Motor 1Rewind$-!Motor 5%1Feed$-Motor%Threshold Manual Fine Adjustment Black Mark/Feed Gap Sensor Black Mark SensorTest Print menu contains the following Print Condition SettingA4.6 Test Print SelectionIssue Count Setting Specifying the Print Condition for the Test PrintSensor Type Selection Print Speed SettingRibbon Type Selection Issue Mode Selection Label Length SettingSlant Line 1 dot Test Print Pattern SelectionPause key Slant Line 3 dotsNon-Printing BarcodeFactory Test A4.7 Dump Mode Auto Print $87235,17 755/$1A4.8.1 Self-Diagnostic Test Result Sample and Descriptions A4.8 Additional InformationSdram 8MB Print Head Resistance Rank Table EXP.I/OTotal Feed ∙ Descriptions of the Maintenance Counter XON+READY Auto A4.8.3 Magnified Views of Slant Line Pattern BusyAppendix 5 Print Samples CODE39 Full Ascii UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digitsUPC-A+2 digits UPC-A+5 digits KIX Code MaxiCodeGlossaries Pre-printed label Index Index