Toshiba R-TH10, B-492L owner manual Total Feed

Page 74

APPENDIX 4 SYSTEM MODE

EO1-33032

A4.8 Additional Information

A4.8.2 Maintenance Counter and Parameter Check Print Sample and Descriptions

∙Print Sample

(1)

(2)

(3)

(4)

(5)

(6)

(7)

(8)

(9)

(10)

(11)

(12)

(13)

(14)

(15)

(16)

(17)

(18)

(19)

(20)

(21)

(22)

(23)

(24)

(25)

(26)

(27)

(28)

(29)

(30)

(31)

(32)

(33)

(34)

(35)

(36)

(37)

(38)

(39)

(40)

(41)

(42)

(43)

TOTAL FEED	1.1Km
FEED	1.1Km
PRINT	0.5Km
HEAD U/D	32
RIBBON	3h
SOLENOID	0h
232C ERR	255
SYSTEM ERR	0
POWER FAIL	0

[PC]		[KEY]
FEED	+2.0mm	FEED	+0.0mm
PEEL OFF	+0.0mm	PEEL OFF	+1.0mm
BACK	+0.0mm	BACK	+0.0mm
TONE(T)	+0 step	TONE(T)	+0 step
TONE (D)	+0 step	TONE(D)	+0 step
RBN(FW)	-10	RBN (FW)	-8
RBN (BK)	+0	RBN (BK)	+0
PO SPEED	+0	PO SPEED	+0
X ADJ.	+0.0mm
THRESHOLD (R)		1.0V
THRESHOLD (T)		1.4V
FONT		[PC-850] [0]
CODE		[AUTO]
RIBBON		[TRANS]
SPEED		[9600]
DATA LENG.		[8]
PARITY		[EVEN]
CONTROL		[XON+READY AUTO]
MESSAGE		[ENGLISH]
RIBBON SAVE		[ON]
FEED KEY		[FEED]
EURO CODE		[B0]
AUTO HD CHK		[OFF]
ACK/BUSY		[TYPE1]
WEB PRINTER		[OFF]
KB80 CONNECT		[OFF]
RIBBON NEAR END		[30m]
PRTR IP ADDRESS		[192.168.010.020]
GATE IP ADDRESS		[000.000.000.000]
SUBNET MASK		[255.255.255.000]
TTF AREA		[704kB]
EXT CHR AREA		[128kB]
PC SAVE AREA		[64kbB
SOCKET PORT		[OFF] [08000]

NOTE:

Print conditions:

Preset count: 1, Print speed: 5”/sec., Sensor: No sensor, Printing mode: Thermal transfer,

Media length: 170 mm, Issue mode: Batch printing

A4-24

Image 74

Contents 492L/R-TH10 Series For QP CE Compliance for EU only For QQWkhsoxj Precautions Request Regarding MaintenanceTable of Contents Appendix 2 Messages and LED Product Overview Introduction FeaturesAccessories UnpackingType DimensionsAppearance of the Printer Front View Type Side ViewType InteriorOperation Panel Appearance of the Power Supply Unit Printer Setup PrecautionsProcedure before Operation Connecting the Cables to Your Printer Connecting the Power Cord Turning OFF the Printer Turning the PrinterTurning on the Printer Causing injury Loading the MediaPaper Holder Media Guide Setting the feed gap sensor position Setting the black mark sensor positionBatch mode Strip modeLoading the Media Loading the Ribbon Pcmcia Cards Test Print Inserting the Optional Pcmcia CardsOn Line Mode Operation PanelOperation To be printedPrint Head/Platen MaintenanceCleaning Media Guide Plate/ Pinch Roller/Sensors Pinch Roller Feed Roller Paper Guide B Locking Screw Paper Holder Covers and PanelsCare/Handling of the Media and Ribbon Error Messages Problems/Causes Solutions TroubleshootingError Messages Restart keyPossible Problems Causes Solutions Possible ProblemsError Messages Problems/Cause Solutions Threshold Setting Removing Jammed MediaThreshold Setting Overview Installing the Printer Drivers Printer OperationSystem Driver InstallationSystem Requirements InterfaceCont Change to the Software License Agreement screenDriver Installation Driver files copy will start Uninstalling the TEC B-492 Printer Driver Uninstalling the TEC B-492 Printer Driver Model 492L/R-TH10-QQ 492L/R-TH10-QP Appendix 1 SpecificationsA1.1 Printer A1.3.1 Media Type A1.2 OptionsA1.3 Media Option Name Type Description SourceA1.3.2 Detection Area of the Transmissive Sensor A1.3.3 Detection Area of the Reflective Sensor A1.3.4 Effective Print AreaA1.4 Ribbon Symbols in the message Appendix 2 Messages and Leds53&$ Appendix 3 Interface „Interface CablesAppendix 4 System Mode A4.1 Operation PanelA4.2 Overview 2PARAMETER SET 5SENSOR ADJ RAM Clear 7IP AddressA4.3 Reset Mode A4.4 Self-Diagnostic TestTest A4.4 Self-DiagnosticMaintenance counter/parameter settings print out Ribbon type selectionPrint head element check 2PAUSE63 567 Feed keyA4.5 Printer Parameter Fine AdjustmentStrip Position Fine Adjustment ContBack Feed Length Fine Adjustment $&.$-PPA4.5 Printer Parameter X Axis Fine Adjustment Cont Feed $-867PPThermal Direct Print PrintThermal Transfer Print Ribbon Motor Voltage Fine Adjustment Feed/Rewind Motor 1Rewind$-!Motor 5%1Feed$-Motor%Threshold Manual Fine Adjustment Black Mark/Feed Gap Sensor Black Mark SensorTest Print menu contains the following Print Condition SettingA4.6 Test Print SelectionIssue Count Setting Specifying the Print Condition for the Test PrintRibbon Type Selection Print Speed SettingSensor Type Selection Issue Mode Selection Label Length SettingSlant Line 1 dot Test Print Pattern SelectionPause key Slant Line 3 dotsFactory Test BarcodeNon-Printing A4.7 Dump Mode Auto Print $87235,17 755/$1A4.8.1 Self-Diagnostic Test Result Sample and Descriptions A4.8 Additional InformationSdram 8MB Print Head Resistance Rank Table EXP.I/OTotal Feed ∙ Descriptions of the Maintenance Counter XON+READY Auto A4.8.3 Magnified Views of Slant Line Pattern BusyAppendix 5 Print Samples CODE39 Full Ascii UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digitsUPC-A+2 digits UPC-A+5 digits KIX Code MaxiCodeGlossaries Pre-printed label Index Index