Toshiba R-TH10, B-492L owner manual Paper Holder Media Guide

Page 18

Paper Entry Guide

2. PRINTER SETUP

EO1-33032

2.7 Loading the Media

2.7Loading the Media (Cont.)

NOTE:

The media guide should be positioned so that the media can feed smoothly.

3. Open the paper entry guide.

4. Loosen the locking screw of the right side of the media guide and open the media guides.

5. Insert each edge of the media into the paper holders of the media guides by adjusting the media guides positions to the media width. Then tighten the locking screw.

Paper Holder

Media Guide

Loose

Locking Screw

6.Pass the media straight from the paper holders to paper outlet. The media should be centred on the strip plate, otherwise skew feeding or a paper jam may occur. Check that the media is positioned so that the distances from the media edge to the end of the scale marked on the strip plate (Distances A and B in the figure below.) are almost equal.

Paper Holder

Strip Plate

Scale

Distances A and B should

be almost equal.

A

Media

B

2- 7

Image 18

Contents 492L/R-TH10 Series For QP CE Compliance for EU only For QQWkhsoxj Precautions Request Regarding MaintenanceTable of Contents Appendix 2 Messages and LED Product Overview Introduction FeaturesAccessories UnpackingDimensions Appearance of the PrinterType Front View Type Side ViewInterior Operation PanelType Appearance of the Power Supply Unit Printer Setup PrecautionsProcedure before Operation Connecting the Cables to Your Printer Connecting the Power Cord Turning the Printer Turning on the PrinterTurning OFF the Printer Causing injury Loading the MediaPaper Holder Media Guide Setting the feed gap sensor position Setting the black mark sensor positionBatch mode Strip modeLoading the Media Loading the Ribbon Pcmcia Cards Test Print Inserting the Optional Pcmcia CardsOn Line Mode Operation PanelOperation To be printedMaintenance CleaningPrint Head/Platen Media Guide Plate/ Pinch Roller/Sensors Pinch Roller Feed Roller Paper Guide B Locking Screw Paper Holder Covers and PanelsCare/Handling of the Media and Ribbon Error Messages Problems/Causes Solutions TroubleshootingError Messages Restart keyPossible Problems Error Messages Problems/Cause SolutionsPossible Problems Causes Solutions Threshold Setting Removing Jammed MediaThreshold Setting Overview Installing the Printer Drivers Printer OperationSystem Driver InstallationSystem Requirements InterfaceCont Change to the Software License Agreement screenDriver Installation Driver files copy will start Uninstalling the TEC B-492 Printer Driver Uninstalling the TEC B-492 Printer Driver Appendix 1 Specifications A1.1 PrinterModel 492L/R-TH10-QQ 492L/R-TH10-QP A1.3.1 Media Type A1.2 OptionsA1.3 Media Option Name Type Description SourceA1.3.2 Detection Area of the Transmissive Sensor A1.3.3 Detection Area of the Reflective Sensor A1.3.4 Effective Print AreaA1.4 Ribbon Symbols in the message Appendix 2 Messages and Leds53&$ Appendix 3 Interface „Interface CablesAppendix 4 System Mode A4.1 Operation PanelA4.2 Overview 2PARAMETER SET 5SENSOR ADJ RAM Clear 7IP AddressA4.3 Reset Mode A4.4 Self-Diagnostic TestTest A4.4 Self-DiagnosticMaintenance counter/parameter settings print out Ribbon type selectionPrint head element check 2PAUSE63 567 Feed keyA4.5 Printer Parameter Fine AdjustmentStrip Position Fine Adjustment ContBack Feed Length Fine Adjustment $&.$-PPA4.5 Printer Parameter X Axis Fine Adjustment Cont Feed $-867PPPrint Thermal Transfer PrintThermal Direct Print Ribbon Motor Voltage Fine Adjustment Feed/Rewind Motor 1Rewind$-!Motor 5%1Feed$-Motor%Threshold Manual Fine Adjustment Black Mark/Feed Gap Sensor Black Mark SensorTest Print menu contains the following Print Condition SettingA4.6 Test Print SelectionIssue Count Setting Specifying the Print Condition for the Test PrintPrint Speed Setting Sensor Type SelectionRibbon Type Selection Issue Mode Selection Label Length SettingSlant Line 1 dot Test Print Pattern SelectionPause key Slant Line 3 dotsBarcode Non-PrintingFactory Test A4.7 Dump Mode Auto Print $87235,17 755/$1A4.8.1 Self-Diagnostic Test Result Sample and Descriptions A4.8 Additional InformationSdram 8MB Print Head Resistance Rank Table EXP.I/OTotal Feed ∙ Descriptions of the Maintenance Counter XON+READY Auto A4.8.3 Magnified Views of Slant Line Pattern BusyAppendix 5 Print Samples CODE39 Full Ascii UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digitsUPC-A+2 digits UPC-A+5 digits KIX Code MaxiCodeGlossaries Pre-printed label Index Index