Toshiba B-492L, R-TH10 owner manual Threshold Setting

Page 35

5. TROUBLESHOOTING

EO1-33032

5.4 Threshold Setting

5.4Threshold Setting (Cont.)

8.Press3$and86(hold the [PAUSE] key until more than 1.5 labels have been issued.

The21media/,1(will continue to be fed until the [PAUSE] key is released.

(Threshold setting for the selected sensor is completed by this operation.)

9.Press21the/,1([RESTART] key.

10.The printer is in stand-by.

11.Send an issue command from the PC to the printer.

5- 4

Image 35

Contents 492L/R-TH10 Series For QQ For QP CE Compliance for EU onlyWkhsoxj Request Regarding Maintenance PrecautionsTable of Contents Appendix 2 Messages and LED Unpacking Introduction FeaturesAccessories Product OverviewType DimensionsAppearance of the Printer Type Side View Front ViewType InteriorOperation Panel Appearance of the Power Supply Unit Precautions Printer SetupProcedure before Operation Connecting the Cables to Your Printer Connecting the Power Cord Turning OFF the Printer Turning the PrinterTurning on the Printer Loading the Media Causing injuryPaper Holder Media Guide Setting the black mark sensor position Setting the feed gap sensor positionStrip mode Batch modeLoading the Media Loading the Ribbon Pcmcia Cards Inserting the Optional Pcmcia Cards Test PrintOperation Panel On Line ModeTo be printed OperationPrint Head/Platen MaintenanceCleaning Media Guide Plate/ Pinch Roller/Sensors Pinch Roller Feed Roller Paper Guide B Locking Screw Covers and Panels Paper HolderCare/Handling of the Media and Ribbon Restart key TroubleshootingError Messages Error Messages Problems/Causes SolutionsPossible Problems Causes Solutions Possible ProblemsError Messages Problems/Cause Solutions Removing Jammed Media Threshold SettingThreshold Setting Printer Operation Overview Installing the Printer DriversInterface Driver InstallationSystem Requirements SystemChange to the Software License Agreement screen ContDriver Installation Driver files copy will start Uninstalling the TEC B-492 Printer Driver Uninstalling the TEC B-492 Printer Driver Model 492L/R-TH10-QQ 492L/R-TH10-QP Appendix 1 SpecificationsA1.1 Printer Option Name Type Description Source A1.2 OptionsA1.3 Media A1.3.1 Media TypeA1.3.2 Detection Area of the Transmissive Sensor A1.3.4 Effective Print Area A1.3.3 Detection Area of the Reflective SensorA1.4 Ribbon Appendix 2 Messages and Leds Symbols in the message53&$ „Interface Cables Appendix 3 InterfaceA4.1 Operation Panel Appendix 4 System Mode2PARAMETER SET 5SENSOR ADJ RAM Clear 7IP Address A4.2 OverviewA4.4 Self-Diagnostic Test A4.3 Reset ModeRibbon type selection A4.4 Self-DiagnosticMaintenance counter/parameter settings print out TestPrint head element check 2PAUSE63 Feed key 567Cont Fine AdjustmentStrip Position Fine Adjustment A4.5 Printer Parameter$&.$-PP Back Feed Length Fine AdjustmentFeed $-867PP A4.5 Printer Parameter X Axis Fine Adjustment ContThermal Direct Print PrintThermal Transfer Print 1Rewind$-!Motor 5%1Feed$-Motor% Ribbon Motor Voltage Fine Adjustment Feed/Rewind MotorBlack Mark Sensor Threshold Manual Fine Adjustment Black Mark/Feed Gap SensorSelection Print Condition SettingA4.6 Test Print Test Print menu contains the followingSpecifying the Print Condition for the Test Print Issue Count SettingRibbon Type Selection Print Speed SettingSensor Type Selection Label Length Setting Issue Mode SelectionSlant Line 3 dots Test Print Pattern SelectionPause key Slant Line 1 dotFactory Test BarcodeNon-Printing Auto Print $87235,17 755/$1 A4.7 Dump ModeA4.8 Additional Information A4.8.1 Self-Diagnostic Test Result Sample and DescriptionsSdram 8MB EXP.I/O Print Head Resistance Rank TableTotal Feed ∙ Descriptions of the Maintenance Counter XON+READY Auto Busy A4.8.3 Magnified Views of Slant Line PatternAppendix 5 Print Samples UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digits CODE39 Full AsciiKIX Code MaxiCode UPC-A+2 digits UPC-A+5 digitsGlossaries Pre-printed label Index Index