Toshiba B-492L, R-TH10 owner manual Appendix 4 System Mode, A4.1 Operation Panel

Page 51

APPENDIX 4 SYSTEM MODE

EO1-33032

A4.1 Operation Panel

APPENDIX 4 SYSTEM MODE

IMPORTANT!

If System Mode is needed for any other purposes, please contact a TOSHIBA TEC authorized service representative before performing any operation in System Mode.

A4.1 Operation Panel

Appendix 4 describes usage of the keys on the Operation Panel in System Mode.

For end users, System Mode should be used for the following five purposes:

To reset the printer. (Reset mode)

To check and print the system status, the Maintenance Counter, and to check the Print Head Elements.

To make fine adjustment to the media handling.

To perform a test print for checking print quality.

To print the raw data being received by the printer (Dump mode).

The figure below shows the Operation Panel and key functions.

LCD Message Display

POWER LED

 

 

 

(Green)

POWER

ON LINE

ERROR

[RESTART] key

 

 

 

[FEED] key

FEED

RESTART

PAUSE

 

ERROR LED (Red)

ON LINE LED (Green)

[PAUSE] key

NOTE:

Use the [RESTART] key to resume printing after a pause condition, or after clearing an error.

The LCD Message Display shows messages to indicate the printer’s current status. Up to 16 characters can be displayed on this line.

There are three LEDs on the Operation Panel.

LED

Illuminates when…

POWER

The printer is turned on.

ON LINE

The printer is ready to print.

ERROR

Any error occurs on the printer.

In System Mode, the [FEED], [RESTART] and [PAUSE] keys function as described below.

FEED

Used to navigate the parameter mode or to fine adjust

the parameters in the negative direction (- Down).

 

 

Used to release the printer from Pause condition, to

 

navigate the parameter mode, or to fine adjust the

RESTART

parameters in the positive direction (+ Up).

By pressing and holding the [RESTART] key in Pause

 

 

condition for more than 3 sec., the printer enters the

 

system mode.

 

Used to stop printing operation temporarily, to select

 

the parameter mode, or used as an enter key.

PAUSE

By pressing and holding the [PAUSE] key in Pause

 

condition for more than 3 sec., the printer enters the

 

threshold setting mode.

A4- 1

Image 51
Contents 492L/R-TH10 Series For QQ For QP CE Compliance for EU onlyWkhsoxj Request Regarding Maintenance PrecautionsTable of Contents Appendix 2 Messages and LED Unpacking Introduction FeaturesAccessories Product OverviewDimensions Appearance of the PrinterType Type Side View Front ViewInterior Operation PanelType Appearance of the Power Supply Unit Precautions Printer SetupProcedure before Operation Connecting the Cables to Your Printer Connecting the Power Cord Turning the Printer Turning on the PrinterTurning OFF the Printer Loading the Media Causing injuryPaper Holder Media Guide Setting the black mark sensor position Setting the feed gap sensor positionStrip mode Batch modeLoading the Media Loading the Ribbon Pcmcia Cards Inserting the Optional Pcmcia Cards Test PrintOperation Panel On Line ModeTo be printed OperationMaintenance CleaningPrint Head/Platen Media Guide Plate/ Pinch Roller/Sensors Pinch Roller Feed Roller Paper Guide B Locking Screw Covers and Panels Paper HolderCare/Handling of the Media and Ribbon Restart key TroubleshootingError Messages Error Messages Problems/Causes SolutionsPossible Problems Error Messages Problems/Cause SolutionsPossible Problems Causes Solutions Removing Jammed Media Threshold SettingThreshold Setting Printer Operation Overview Installing the Printer DriversInterface Driver InstallationSystem Requirements SystemChange to the Software License Agreement screen ContDriver Installation Driver files copy will start Uninstalling the TEC B-492 Printer Driver Uninstalling the TEC B-492 Printer Driver Appendix 1 Specifications A1.1 PrinterModel 492L/R-TH10-QQ 492L/R-TH10-QP Option Name Type Description Source A1.2 OptionsA1.3 Media A1.3.1 Media TypeA1.3.2 Detection Area of the Transmissive Sensor A1.3.4 Effective Print Area A1.3.3 Detection Area of the Reflective SensorA1.4 Ribbon Appendix 2 Messages and Leds Symbols in the message53&$ „Interface Cables Appendix 3 InterfaceA4.1 Operation Panel Appendix 4 System Mode2PARAMETER SET 5SENSOR ADJ RAM Clear 7IP Address A4.2 OverviewA4.4 Self-Diagnostic Test A4.3 Reset ModeRibbon type selection A4.4 Self-DiagnosticMaintenance counter/parameter settings print out TestPrint head element check 2PAUSE63 Feed key 567Cont Fine AdjustmentStrip Position Fine Adjustment A4.5 Printer Parameter$&.$-PP Back Feed Length Fine AdjustmentFeed $-867PP A4.5 Printer Parameter X Axis Fine Adjustment ContPrint Thermal Transfer PrintThermal Direct Print 1Rewind$-!Motor 5%1Feed$-Motor% Ribbon Motor Voltage Fine Adjustment Feed/Rewind MotorBlack Mark Sensor Threshold Manual Fine Adjustment Black Mark/Feed Gap SensorSelection Print Condition SettingA4.6 Test Print Test Print menu contains the followingSpecifying the Print Condition for the Test Print Issue Count SettingPrint Speed Setting Sensor Type SelectionRibbon Type Selection Label Length Setting Issue Mode SelectionSlant Line 3 dots Test Print Pattern SelectionPause key Slant Line 1 dotBarcode Non-PrintingFactory Test Auto Print $87235,17 755/$1 A4.7 Dump ModeA4.8 Additional Information A4.8.1 Self-Diagnostic Test Result Sample and DescriptionsSdram 8MB EXP.I/O Print Head Resistance Rank TableTotal Feed ∙ Descriptions of the Maintenance Counter XON+READY Auto Busy A4.8.3 Magnified Views of Slant Line PatternAppendix 5 Print Samples UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digits CODE39 Full AsciiKIX Code MaxiCode UPC-A+2 digits UPC-A+5 digitsGlossaries Pre-printed label Index Index