Sharp SRT-8168 ON-SCREEN Menu, Main Menu, Using the JOG dial and Shuttle ring for settings

Page 10

RF4QR/NA (SRT-8960 GB) Wed. May, 08/2002

ON-SCREEN MENU

Main Menu

To access on-screen menu

1When no menu is displayed on-screen, press the MENU button.

øThe MAIN MENU appears.

MAIN MENU

<MAIN@MENU>

1.LANGUAGE/CLOCK@SET

2.DISPLAY/SW@OUT@SET

3.GENERAL@SET

4.WARNING@OUT/CONTR.SET

5.ALARM/SERIES@REC@SET

6.TAPE@MANAGEMENT

7.TIMER@SET

8.HOLIDAY@SET

9.OTHERS

2Press the MENU EXIT (or MENU) button to return to the monitor screen.

Using the JOG dial and SHUTTLE ring for settings

JOG dial

Put the tip of your index finger into the depression, then turn the dial in any direction.

œWhen the display is highlighted in a sub-menu, turn the dial to select the setting item.

œWhen the display is highlighted in a MAIN MENU, select a sub-menu.

œWhile the display is flashing, turn the dial and the selected data setting will change or the selected setting value will increase or decrease.

SHUTTLE ring

œWhen a menu is being displayed, turn the ring 10° or more clockwise to change the selected setting item from highlighted to flashing.

œAfter making the setting, turn the ring clockwise to save the setting and move to the next setting.

œWhen a MAIN MENU is being displayed, turn the ring clockwise and the sub-menu for selection will appear.

œWhen a sub-menu is being displayed, turn the ring counterclockwise and the MAIN MENU will appear.

œIf there are several items on one line, turn the ring clockwise to move to the next item (on the right) and confirm the setting. Turning the ring counterclockwise will restore the original setting condition and move to the previous item (on the left).

Sub-menus

To enter or modify settings within a sub-menu

1When a MAIN MENU is being displayed, turn the JOG dial to select one of the sub-menus, then turn the SHUTTLE ring clockwise.

øThe selected sub-menu appears.

2Turn the JOG dial to move the selection to the desired setting, then turn the SHUTTLE ring clockwise.

øThe selected item flashes.

3Turn the JOG dial to enter or modify the setting.

4Press the MENU EXIT button to save the settings and return to the monitor screen.

LANGUAGE/CLOCK SET menu

<LANGUAGE/CLOCK@SET>

*LANGUAGE-LANGUE-IDIOMA

@@@@@@@@@@@@@@@ENGLISH

*CLOCK@SET @01-01-2002@TUE@00:00:00

*DAYLIGHT@SET@@@@@NO@USE

@@@@@@WEEK@@@MONTH@TIME

@ON@@@1ST-SUN@@04@@02:00 @OFF@@LST-SUN@@10@@02:00

DISPLAY/SW OUT SET menu

<DISPLAY@SET>@@@@SET@UP

DATE@@@@@@@@@@@@@Y

TIME@@@@@@@@@@@@@Y

SPEED@@@@@@@@@@@@Y

ALARM@COUNT@@@@@@Y

<SW@OUT@SET>

TIMING@@@@@@@@@@@FIELD

FIELD@@@@@@@@@@@@1

8H@MODE@@@@@@@@@@Y

GENERAL SET menu

<GENERAL@SET>

TAPE@IN@MODE@@@@@STOP

TAPE@END@MODE@@@@REW

CLOCK@ADJUST@@@@@01:00

THREAD@CHECK@@@@@N

VIDEO@LOSS@@@@@@@N

CLOG@DETECT.@@@@@N

REMOTE@@@@@@@@@@@MENU

VIDEO@@@@@@@@@@@@COLOR

VERTICAL@SYNC@@@@Y TAPE@@@@@@@@@@@@@T-160

English

9

Page 9 Page 11
Image 10
Page 9 Page 11
Contents SRT-8960 SRT-8168 SRT-8040 Precautions For customers in CanadaLocation PrecautionsMoisture Condensation Problems Avoiding Electrical Shock and FireFeatures ContentsAccessory Locations of Controls and Indicators Front PanelOperation Mode Indicator Locations of Controls and IndicatorsOperation Indicators Digital DisplayWith the RS-485/232C interface board Back Panel With the RS-485/232C interface board B C DPower Cord Installation ConnectionsMain Menu Using the JOG dial and Shuttle ring for settingsON-SCREEN Menu Sub-menusON-SCREEN Menu Language Setting Setting the Language and ClockClock setting Automatic Daylight Saving Time Adjustment Setting the Language and ClockFactory setting Selecting the Superimpose Display Superimpose DisplayChanging the Superimpose Display Position Video Cassette Tapes Video Cassette Tapes Setting the Action to Take When a Cassette is LoadedSetting the Type of Tape Used Correct tape thread check functionIf no tape management data is present on the tape Tape ManagementOperation If tape management data is present on the tapeTape Management Setting the Tape Management FunctionTape Management menu appears Tape Management Conflict Display Conflict display sampleNormal Recording Recording Speed ModeNormal Recording Before startingRecord Pause Pause/still indicator N flashesNormal Recording Recording CheckAction to Take when the Video Signal Deteriorates Setting the clog detectionClog Detection Setting when not using Autorepeat recording Setting the Mode at the End of the TapeSetting the video input signal Setting when using Autorepeat recordingAutorepeat Recording Repeat indicator lightsAutorepeat Recording Alarm Recording Setting Alarm RecordingALARM/SERIES REC SET menu appears Alarm Recording Counter Display Alarm RecordingAlarm Recording Reset Function Connections to the Alarm in TerminalAlarm Search Alarm ScanProgram Timer Recording Program Timer Recording Timer SET menu appearsTo Cancel a Program Timer Recording Setting the HolidaysChanging a Program Timer Recording To cancel all program timer recordingsThese portions will not be recorded Recording Using AN External Timer Input Operation Series Recording SetupSeries Recording Loop recordingSingle Image Recording Setup Single Image RecordingNormal Playback Special Playback Special Playback Shuttle Ring OperationTape Counter DAY/TIME SearchDay/Time Search Security Lock Setting the 4 digit security lockCancel the 4 digit security lock Quick Method Security LockSelecting Input and Output Terminals Clock AdjustmentConnection Eject output Timer OUT terminal Setting the Cassette Eject ModeCassette Eject Setup Eject input Series in terminalOperator Mode Synchronization ControlSynchronization Control Setting the Cassette Eject ModeAdministrator/Installer Mode SC will flash on the digital displaySetting the Address and Data Transfer Speed Setting for RS-485 or RS-232C USESettings when using RS-485 Power FAILURE/DEW/USED Time menu appears Output Terminals Timer OUT terminalTape END OUT Terminal Output Setting Tape END OUT TerminalOutput Terminals SW OUT Terminal Output SettingSW OUT Terminal ALARM@@@@@@@@@@@@Y NON@REC@@@@@@@@@@N Remote control setting Remote JackMaintenance Maintenance Table MaintenanceMaintaining and Checking The Mechanism After a Power Failure Troubleshooting GuideSystem Down Connectors SpecificationsGeneral Specifications VideoOther Specifications SpecificationsConnectors When the Terminal SET is set to SET2 Sanyo Industrial VCR Warranty Weekdays 830 AM 500 PM Pacific Time
Top Page Image Contents