Sharp SRT-8168 Video Cassette Tapes, Correct tape thread check function, General SET menu appears

Page 16

RF4QR/NA (SRT-8960 GB) Wed. May, 08/2002

VIDEO CASSETTE TAPES

Correct tape thread check function

This function checks to make sure that the cassette has been correctly loaded so that recording can be carried out.

NOTES:

œAfter the cassette tape is loaded, the mechanism will operate for about 5 seconds to check that the tape

has been threaded (loaded) correctly automatically and the cassette indicator “o” will flash during that period. If the tape is not loaded properly, the cassette will be ejected.

œIf the REC, PLAY or STOP button is pressed or if the SHUTTLE ring is turned during the tape thread check operation, the command will only be executed after the tape thread has been checked. Only the EJECT button will operate while the tape thread is being checked.

œIf “TAPE IN MODE” in the (GENERAL SET) menu is set to “REC”, the recording indicator “m” will light while the tape thread is being checked. However, recording will only start after the tape thread check is completed.

1Press the MENU button to display the MAIN MENU.

2Turn the JOG dial to select the “3.GENERAL SET” line, then turn the SHUTTLE ring clockwise.

øThe (GENERAL SET) menu appears.

<GENERAL@SET>

TAPE@IN@MODE@@@@@STOP

TAPE@END@MODE@@@@REW

CLOCK@ADJUST@@@@@01:00

THREAD@CHECK@@@@@N

VIDEO@LOSS@@@@@@@N

CLOG@DETECT.@@@@@N

REMOTE@@@@@@@@@@@MENU

VIDEO@@@@@@@@@@@@COLOR

VERTICAL@SYNC@@@@Y TAPE@@@@@@@@@@@@@T-160

3Turn the JOG dial until the “THREAD CHECK” setting is highlighted, then turn the SHUTTLE ring clockwise.

4Turn the JOG dial to select the desired mode, then turn the SHUTTLE ring clockwise.

N. . . . . . . . . The correct tape thread check function is off

Y. . . . . . . . . . The correct tape thread check function is on

5Press the MENU EXIT button.

Setting the Action to Take When a Cassette is Loaded

You can set the mode the VCR will go into when a cassette is loaded.

1Press the MENU button to display the MAIN MENU.

2Turn the JOG dial to select the “3.GENERAL SET” line, then turn the SHUTTLE ring clockwise.

øThe (GENERAL SET) menu appears.

3Turn the JOG dial until the “TAPE IN MODE” setting is highlighted, then turn the SHUTTLE ring clockwise.

4Turn the JOG dial to select the desired mode, then turn the SHUTTLE ring clockwise.

STOP . . . . . . When tape inserted the VCR, stays in stop mode

REC . . . . . . . When tape inserted the VCR, goes into recording mode

5Press the MENU EXIT button.

Setting the Type of Tape Used

1Press the MENU button to display the MAIN MENU.

2Turn the JOG dial to select the “3.GENERAL SET” line, then turn the SHUTTLE ring clockwise.

øThe (GENERAL SET) menu appears.

3Turn the JOG dial until the “TAPE” setting is highlighted, then turn the SHUTTLE ring clockwise.

4Turn the JOG dial to set the tape length, then turn the SHUTTLE ring clockwise.

T-160 . . . . . . When using a T-160 cassette tape

T-120 . . . . . . When using a T-120 cassette tape

5Press the MENU EXIT button.

English

15

Image 16
Contents SRT-8960 SRT-8168 SRT-8040 Precautions For customers in CanadaPrecautions Moisture Condensation ProblemsLocation Avoiding Electrical Shock and FireFeatures ContentsAccessory Locations of Controls and Indicators Front PanelLocations of Controls and Indicators Operation IndicatorsOperation Mode Indicator Digital DisplayWith the RS-485/232C interface board Back Panel With the RS-485/232C interface board B C DPower Cord Installation ConnectionsUsing the JOG dial and Shuttle ring for settings ON-SCREEN MenuMain Menu Sub-menusON-SCREEN Menu Language Setting Setting the Language and ClockClock setting Automatic Daylight Saving Time Adjustment Setting the Language and ClockFactory setting Selecting the Superimpose Display Superimpose DisplayChanging the Superimpose Display Position Video Cassette Tapes Setting the Action to Take When a Cassette is Loaded Setting the Type of Tape UsedVideo Cassette Tapes Correct tape thread check functionTape Management OperationIf no tape management data is present on the tape If tape management data is present on the tapeTape Management Setting the Tape Management FunctionTape Management menu appears Tape Management Conflict Display Conflict display sampleRecording Speed Mode Normal RecordingNormal Recording Before startingPause/still indicator N flashes Normal RecordingRecord Pause Recording CheckAction to Take when the Video Signal Deteriorates Setting the clog detectionClog Detection Setting the Mode at the End of the Tape Setting the video input signalSetting when not using Autorepeat recording Setting when using Autorepeat recordingAutorepeat Recording Repeat indicator lightsAutorepeat Recording Alarm Recording Setting Alarm RecordingALARM/SERIES REC SET menu appears Alarm Recording Alarm Recording Reset FunctionAlarm Recording Counter Display Connections to the Alarm in TerminalAlarm Search Alarm ScanProgram Timer Recording Program Timer Recording Timer SET menu appearsSetting the Holidays Changing a Program Timer RecordingTo Cancel a Program Timer Recording To cancel all program timer recordingsThese portions will not be recorded Recording Using AN External Timer Input Series Recording Setup Series RecordingOperation Loop recordingSingle Image Recording Setup Single Image RecordingNormal Playback Special Playback Special Playback Shuttle Ring OperationTape Counter DAY/TIME SearchDay/Time Search Setting the 4 digit security lock Cancel the 4 digit security lockSecurity Lock Quick Method Security LockSelecting Input and Output Terminals Clock AdjustmentConnection Setting the Cassette Eject Mode Cassette Eject SetupEject output Timer OUT terminal Eject input Series in terminalOperator Mode Synchronization ControlSetting the Cassette Eject Mode Administrator/Installer ModeSynchronization Control SC will flash on the digital displaySetting the Address and Data Transfer Speed Setting for RS-485 or RS-232C USESettings when using RS-485 Power FAILURE/DEW/USED Time menu appears Timer OUT terminal Tape END OUT Terminal Output SettingOutput Terminals Tape END OUT TerminalOutput Terminals SW OUT Terminal Output SettingSW OUT Terminal ALARM@@@@@@@@@@@@Y NON@REC@@@@@@@@@@N Remote control setting Remote JackMaintenance Maintenance Table MaintenanceMaintaining and Checking The Mechanism After a Power Failure Troubleshooting GuideSystem Down Specifications General SpecificationsConnectors VideoOther Specifications SpecificationsConnectors When the Terminal SET is set to SET2 Sanyo Industrial VCR Warranty Weekdays 830 AM 500 PM Pacific Time