Sharp SRT-8168, SRT-8960, SRT-8040 instruction manual Remote Jack, Remote control setting

Page 49

RF4QR/NA (SRT-8960 GB) Wed. May, 08/2002

OUTPUT TERMINALS

REMOTE Jack

Remote control of the VCR is possible by connecting a remote controller with a circuit such as indicated below, to the REMOTE jack.

NOTES:

œUse a 3.5 mm mini-jack type plug.

œThe connection should be done using a shielded cable no more than 5 meters long.

œThe functions not available on the VCR will not operate.

œYou can use a VA-RMN01 Remote Control Unit (sold separately) to control the VCR remotely. The functions not available on the VCR will not operate.

Remote control circuit

Remote control setting

The remote control switch 7 (see illustration at left) can be set to either eject the tape or access the menus.

1Press the MENU button to display the MAIN MENU.

2Turn the JOG dial to select the “3.GENERAL SET” line, then turn the SHUTTLE ring clockwise.

øThe (GENERAL SET) menu appears.

<GENERAL@SET>

TAPE@IN@MODE@@@@@STOP

TAPE@END@MODE@@@@REW

CLOCK@ADJUST@@@@@01:00

THREAD@CHECK@@@@@N

VIDEO@LOSS@@@@@@@N

CLOG@DETECT.@@@@@N

REMOTE@@@@@@@@@@@MENU

VIDEO@@@@@@@@@@@@COLOR

VERTICAL@SYNC@@@@Y TAPE@@@@@@@@@@@@@T-160

3Turn the JOG dial until the “REMOTE” setting is highlighted, then turn the SHUTTLE ring clockwise.

R0 1.2K

R1 0.3K

R2 0.43K

R3 0.51K

R4 0.62K

R5 0.75K

R6 0.91K

R7 1.1K

R8 1.3K

R9 2.0K

R10 2.4K

R11 3.6K

R12 5.6K

The resistance tolerance is 2% or less.

SW0: EJECT

SW1: STOP

SW2: STILL/PAUSE

SW3: REW

SW4: FF

SW5: PLAY

SW6: REC

SW7: MENU (or EJECT)

SW8: REV

SW9: REC/PLAY SPEED j

SW10: REC/PLAY SPEED l

SW11: SHIFT ]

SW12: SHIFT «

4Turn the JOG dial to select the desired switch mode, then turn the SHUTTLE ring clockwise.

MENU. . . . . . Switch operates as an MENU button

EJECT . . . . . Switch operates as an EJECT button

5Press the MENU EXIT button.

48

English

Image 49

Contents SRT-8960 SRT-8168 SRT-8040 For customers in Canada PrecautionsMoisture Condensation Problems PrecautionsLocation Avoiding Electrical Shock and FireFeatures ContentsAccessory Front Panel Locations of Controls and IndicatorsOperation Indicators Locations of Controls and IndicatorsOperation Mode Indicator Digital DisplayWith the RS-485/232C interface board B C D Back Panel With the RS-485/232C interface boardConnections Power Cord InstallationON-SCREEN Menu Using the JOG dial and Shuttle ring for settingsMain Menu Sub-menusON-SCREEN Menu Language Setting Setting the Language and ClockClock setting Automatic Daylight Saving Time Adjustment Setting the Language and ClockFactory setting Selecting the Superimpose Display Superimpose DisplayChanging the Superimpose Display Position Video Cassette Tapes Setting the Type of Tape Used Setting the Action to Take When a Cassette is LoadedVideo Cassette Tapes Correct tape thread check functionOperation Tape ManagementIf no tape management data is present on the tape If tape management data is present on the tapeTape Management Setting the Tape Management FunctionTape Management menu appears Conflict display sample Tape Management Conflict DisplayNormal Recording Recording Speed ModeNormal Recording Before startingNormal Recording Pause/still indicator N flashesRecord Pause Recording CheckAction to Take when the Video Signal Deteriorates Setting the clog detectionClog Detection Setting the video input signal Setting the Mode at the End of the TapeSetting when not using Autorepeat recording Setting when using Autorepeat recordingAutorepeat Recording Repeat indicator lightsAutorepeat Recording Alarm Recording Setting Alarm RecordingALARM/SERIES REC SET menu appears Alarm Recording Reset Function Alarm RecordingAlarm Recording Counter Display Connections to the Alarm in TerminalAlarm Scan Alarm SearchProgram Timer Recording Timer SET menu appears Program Timer RecordingChanging a Program Timer Recording Setting the HolidaysTo Cancel a Program Timer Recording To cancel all program timer recordingsThese portions will not be recorded Recording Using AN External Timer Input Series Recording Series Recording SetupOperation Loop recordingSingle Image Recording Single Image Recording SetupNormal Playback Special Playback Shuttle Ring Operation Special PlaybackTape Counter DAY/TIME SearchDay/Time Search Cancel the 4 digit security lock Setting the 4 digit security lockSecurity Lock Quick Method Security LockSelecting Input and Output Terminals Clock AdjustmentConnection Cassette Eject Setup Setting the Cassette Eject ModeEject output Timer OUT terminal Eject input Series in terminalSynchronization Control Operator ModeAdministrator/Installer Mode Setting the Cassette Eject ModeSynchronization Control SC will flash on the digital displaySetting the Address and Data Transfer Speed Setting for RS-485 or RS-232C USESettings when using RS-485 Power FAILURE/DEW/USED Time menu appears Tape END OUT Terminal Output Setting Timer OUT terminalOutput Terminals Tape END OUT TerminalOutput Terminals SW OUT Terminal Output SettingSW OUT Terminal ALARM@@@@@@@@@@@@Y NON@REC@@@@@@@@@@N Remote Jack Remote control settingMaintenance Maintenance Table MaintenanceMaintaining and Checking The Mechanism After a Power Failure Troubleshooting GuideSystem Down General Specifications SpecificationsConnectors VideoOther Specifications SpecificationsConnectors When the Terminal SET is set to SET2 Weekdays 830 AM 500 PM Pacific Time Sanyo Industrial VCR Warranty