Sharp SRT-8960, SRT-8168 Setting the Tape Management Function, Tape Management menu appears

Page 18

RF4QR/NA (SRT-8960 GB) Wed. May, 08/2002

TAPE MANAGEMENT

Setting the Tape Management Function

1Press the MENU button to display the MAIN MENU.

2Turn the JOG dial to select the “6.TAPE MANEGEMENT” line, then turn the SHUTTLE ring clockwise.

øThe (TAPE MANAGEMENT) menu appears.

<TAPE@MANAGEMENT>

*TAPE@MANAGEMENT@@@@N

*PROTECT@DAY@@@@@@@30

*REC@PASS@SET@@@@@@10

*GROUP@NO.SET@@@@@OFF

*OVERRIDE@@@@@@@@@@@N

3Turn the SHUTTLE ring clockwise.

4Turn the JOG dial to select the desired mode, then turn the SHUTTLE ring clockwise.

N. . . . . . . The tape management function is not active.

Y. . . . . . . The tape management function is active.

When setting to “Y”, please continue with the settings below.

5Turn the JOG dial until the “PROTECT DAY” setting is highlighted, then turn the SHUTTLE ring clockwise.

6Turn the JOG dial to select the desired number of days to protect the tape, then turn the SHUTTLE ring clockwise.

OFF . . . . The tape is not protected

1-255 . . . Number of days to protect the tape (prevent over-recording), from the date of the last recording on the tape (or the last expected recording date (calculated using the tape length (T-120 or T-160) and the recording speed)).

NOTE:

œSince the last expected recording date is a calculated date (using the tape length (T-120 or T-160) and the recording speed), it may be different from the actual last recording date, due to other settings such as alarm recordings, program timer recordings and holiday settings.

7Turn the JOG dial until the “REC PASS SET” setting is highlighted, then turn the SHUTTLE ring clockwise.

8Turn the JOG dial to select the desired number of re-recording times, then turn the SHUTTLE ring clockwise.

OFF . . . . The number of re-recording times will not be checked.

1-100 . . . Maximum number of re-recording times. (Refer to “Concerning the Number of Times Tapes can be Rerecorded on” on page 20.)

NOTES:

œSince data is read before it is recorded, the number of times will be incremented even if the recording is stopped before the end.

œDuring autorepeat recording, the re-recording times count will be updated every time the tape is rewound to the beginning. Autorepeat recording will proceed even if the count exceeds the “REC PASS SET” setting.

9Turn the JOG dial until the “GROUP NO. SET” setting is highlighted, then turn the SHUTTLE ring clockwise.

FTurn the JOG dial to select the desired group number, then turn the SHUTTLE ring clockwise.

OFF . . . . The group number will not be checked.

1-15 . . . . Group number setting.

GTurn the JOG dial until the “OVERRIDE” setting is highlighted, then turn the SHUTTLE ring clockwise.

HTurn the JOG dial to select the desired override mode, then turn the SHUTTLE ring clockwise. (Refer to “Tape Management Conflict Display” on the next page.)

N. . . . . . . Only EJECT button operation is accepted after a conflict has occurred.

Y. . . . . . . The next operation is accepted after a conflict has occurred. This will override setting.

IPress the MENU EXIT button.

NOTES:

œOnce the tape management data is recorded on tape, it cannot be changed.

œThe criteria (condition) for allowing recording will be based on the data recorded on the tape and not the settings in the (TAPE MANAGEMENT) menu.

English

17

Image 18
Contents SRT-8960 SRT-8168 SRT-8040 Precautions For customers in CanadaLocation PrecautionsMoisture Condensation Problems Avoiding Electrical Shock and FireContents FeaturesAccessory Locations of Controls and Indicators Front PanelOperation Mode Indicator Locations of Controls and IndicatorsOperation Indicators Digital DisplayWith the RS-485/232C interface board Back Panel With the RS-485/232C interface board B C DPower Cord Installation ConnectionsMain Menu Using the JOG dial and Shuttle ring for settingsON-SCREEN Menu Sub-menusON-SCREEN Menu Setting the Language and Clock Language SettingClock setting Setting the Language and Clock Automatic Daylight Saving Time AdjustmentFactory setting Superimpose Display Selecting the Superimpose DisplayChanging the Superimpose Display Position Video Cassette Tapes Video Cassette Tapes Setting the Action to Take When a Cassette is LoadedSetting the Type of Tape Used Correct tape thread check functionIf no tape management data is present on the tape Tape ManagementOperation If tape management data is present on the tapeSetting the Tape Management Function Tape ManagementTape Management menu appears Tape Management Conflict Display Conflict display sampleNormal Recording Recording Speed ModeNormal Recording Before startingRecord Pause Pause/still indicator N flashesNormal Recording Recording CheckSetting the clog detection Action to Take when the Video Signal DeterioratesClog Detection Setting when not using Autorepeat recording Setting the Mode at the End of the TapeSetting the video input signal Setting when using Autorepeat recordingRepeat indicator lights Autorepeat RecordingAutorepeat Recording Alarm Recording Alarm Recording SettingALARM/SERIES REC SET menu appears Alarm Recording Counter Display Alarm RecordingAlarm Recording Reset Function Connections to the Alarm in TerminalAlarm Search Alarm ScanProgram Timer Recording Program Timer Recording Timer SET menu appearsTo Cancel a Program Timer Recording Setting the HolidaysChanging a Program Timer Recording To cancel all program timer recordingsThese portions will not be recorded Recording Using AN External Timer Input Operation Series Recording SetupSeries Recording Loop recordingSingle Image Recording Setup Single Image RecordingNormal Playback Special Playback Special Playback Shuttle Ring OperationDAY/TIME Search Tape CounterDay/Time Search Security Lock Setting the 4 digit security lockCancel the 4 digit security lock Quick Method Security LockClock Adjustment Selecting Input and Output TerminalsConnection Eject output Timer OUT terminal Setting the Cassette Eject ModeCassette Eject Setup Eject input Series in terminalOperator Mode Synchronization ControlSynchronization Control Setting the Cassette Eject ModeAdministrator/Installer Mode SC will flash on the digital displaySetting for RS-485 or RS-232C USE Setting the Address and Data Transfer SpeedSettings when using RS-485 Power FAILURE/DEW/USED Time menu appears Output Terminals Timer OUT terminalTape END OUT Terminal Output Setting Tape END OUT TerminalSW OUT Terminal Output Setting Output TerminalsSW OUT Terminal ALARM@@@@@@@@@@@@Y NON@REC@@@@@@@@@@N Remote control setting Remote JackMaintenance Maintenance Maintenance TableMaintaining and Checking The Mechanism Troubleshooting Guide After a Power FailureSystem Down Connectors SpecificationsGeneral Specifications VideoSpecifications Other SpecificationsConnectors When the Terminal SET is set to SET2 Sanyo Industrial VCR Warranty Weekdays 830 AM 500 PM Pacific Time