Sharp SRT-8960, SRT-8168 Series Recording Setup, Operation, Loop recording, Connection

Page 33

RF4QR/NA (SRT-8960 GB) Wed. May, 08/2002

SERIES RECORDING

Using 2 VCRs or more, the series recording function lets you switch recording from one unit to the next (only with VCRs of the same model as this one).

Series Recording Setup

œConnect 2 VCRs or more as illustrated below.

œSet the “TAPE” item in the (GENERAL SET) menu according to the duration of the tape used.

1Press the REC/PLAY SPEED l (or j) button to set the recording speed mode.

2Set the following items as indicated.

Item

VCR No.1

VCR No.2

 

 

and on

Cassette tape

Loaded

Loaded

Operation mode

Stop

Stop

“TAPE END MODE”(in

REW,

REW,

(GENERAL SET) menu)

STOP or

STOP or

 

EJECT

EJECT

“SERIES REC” (in

 

 

(ALARM/SERIES REC

Y (YES)

Y (YES)

SET) menu)

 

 

Timer recording

OFF (not

OFF (not

 

set)

set)

Security lock

Canceled

Set

 

 

 

3Press the REC button on VCR No.1.

øRecording will start in series recording mode.

4Set the security lock on VCR No.1.

Connection

Operation

The output signal at the TAPE END OUT terminal will be present either at the point when the counter reading is 8H 00M 00S or when VCR No. 1 reaches the end of the tape, whichever is first.

When this signal is received by VCR No. 2, it will start recording.

When the tape end is reached, operation is then carried out according to the “TAPE END MODE” setting in the (GENERAL SET) menu.

NOTES:

œWhen using tapes that are based on the VHS standard, a single tape can be used to record 8H 00M 00S or more based on the counter setting (6H 00M 00S or more when the “TAPE” in (GENERAL SET) menu is set to “T-120”).

œIf “SERIES REC” is set to “N” in the (ALARM/SERIES REC SET) menu, series recording will not be possible.

œThe counter must start from the beginning of tape, or the series recording out will not function properly.

œEven if “OFF” is displayed, series recording will be conducted if there is an input at the SERIES IN terminal.

Loop recording

œConnect the output from the TAPE END OUT terminal of the last VCR to the SERIES IN terminal of the first VCR.

œThe “TAPE END MODE” in (GENERAL SET) menu should be set to “REW” for all units without fail.

œIn loop recording mode, the tape will be re-recorded over. If you need to keep the recorded information, please eject the tape after recording is complete and insert a new tape.

Video camera

VCR No. 1

Monitor TV

 

 

Series recording

 

 

 

 

 

 

Loop recording

 

 

 

 

 

To VIDEO OUT jack

To VIDEO IN jack

VCR No. 2

SERIES IN

COM TAPE END OUT

VIDEO IN VIDEO OUT

SERIES IN

COM TAPE END OUT

VIDEO IN VIDEO OUT

To SERIES IN terminal

To COM terminal

32

English

Page 32 Page 34
Image 33
Page 32 Page 34
Contents SRT-8960 SRT-8168 SRT-8040 For customers in Canada PrecautionsMoisture Condensation Problems PrecautionsLocation Avoiding Electrical Shock and FireContents FeaturesAccessory Front Panel Locations of Controls and IndicatorsOperation Indicators Locations of Controls and IndicatorsOperation Mode Indicator Digital DisplayWith the RS-485/232C interface board B C D Back Panel With the RS-485/232C interface boardConnections Power Cord InstallationON-SCREEN Menu Using the JOG dial and Shuttle ring for settingsMain Menu Sub-menusON-SCREEN Menu Setting the Language and Clock Language SettingClock setting Setting the Language and Clock Automatic Daylight Saving Time AdjustmentFactory setting Superimpose Display Selecting the Superimpose DisplayChanging the Superimpose Display Position Video Cassette Tapes Setting the Type of Tape Used Setting the Action to Take When a Cassette is LoadedVideo Cassette Tapes Correct tape thread check functionOperation Tape ManagementIf no tape management data is present on the tape If tape management data is present on the tapeSetting the Tape Management Function Tape ManagementTape Management menu appears Conflict display sample Tape Management Conflict DisplayNormal Recording Recording Speed ModeNormal Recording Before startingNormal Recording Pause/still indicator N flashesRecord Pause Recording CheckSetting the clog detection Action to Take when the Video Signal DeterioratesClog Detection Setting the video input signal Setting the Mode at the End of the TapeSetting when not using Autorepeat recording Setting when using Autorepeat recordingRepeat indicator lights Autorepeat RecordingAutorepeat Recording Alarm Recording Alarm Recording SettingALARM/SERIES REC SET menu appears Alarm Recording Reset Function Alarm RecordingAlarm Recording Counter Display Connections to the Alarm in TerminalAlarm Scan Alarm SearchProgram Timer Recording Timer SET menu appears Program Timer RecordingChanging a Program Timer Recording Setting the HolidaysTo Cancel a Program Timer Recording To cancel all program timer recordingsThese portions will not be recorded Recording Using AN External Timer Input Series Recording Series Recording SetupOperation Loop recordingSingle Image Recording Single Image Recording SetupNormal Playback Special Playback Shuttle Ring Operation Special PlaybackDAY/TIME Search Tape CounterDay/Time Search Cancel the 4 digit security lock Setting the 4 digit security lockSecurity Lock Quick Method Security LockClock Adjustment Selecting Input and Output TerminalsConnection Cassette Eject Setup Setting the Cassette Eject ModeEject output Timer OUT terminal Eject input Series in terminalSynchronization Control Operator ModeAdministrator/Installer Mode Setting the Cassette Eject ModeSynchronization Control SC will flash on the digital displaySetting for RS-485 or RS-232C USE Setting the Address and Data Transfer SpeedSettings when using RS-485 Power FAILURE/DEW/USED Time menu appears Tape END OUT Terminal Output Setting Timer OUT terminalOutput Terminals Tape END OUT TerminalSW OUT Terminal Output Setting Output TerminalsSW OUT Terminal ALARM@@@@@@@@@@@@Y NON@REC@@@@@@@@@@N Remote Jack Remote control settingMaintenance Maintenance Maintenance TableMaintaining and Checking The Mechanism Troubleshooting Guide After a Power FailureSystem Down General Specifications SpecificationsConnectors VideoSpecifications Other SpecificationsConnectors When the Terminal SET is set to SET2 Weekdays 830 AM 500 PM Pacific Time Sanyo Industrial VCR Warranty
Top Page Image Contents