Sharp SRT-8960, SRT-8168, SRT-8040 instruction manual Synchronization Control, Operator Mode

Page 42

RF4QR/NA (SRT-8960 GB) Wed. May, 08/2002

SYNCHRONIZATION CONTROL

When two or more VCRs are connected together, the VCRs can be operated simultaneously just by operating the VCR that has been set to “MASTER”, without using a system controller (sold separately).

There are two modes available: operator mode and administrator/installer mode. The operations that can be carried out in each mode are different.

NOTES:

œ The operation and setting can only be carried out with

the button of this unit.

œ Use cables with a thickness of A.W.G.24 (0.2 mm2) or

more and a length no more than 1.5 m to connect

VCRs.

œ It is recommended that you do not connect any more

than 10 VCRs together.

œ Only one VCR can be specified at the master unit.

œ Do not mix operator mode and administrator/installer

mode in the same installation.

œ Do not connect the VCRs in a loop.

œ “TERMINAL SET” in the (OTHERS) menu should

always be set to “SET1”.

œ The VCR operation may not e completely

synchronized depending on the VCR statuses, the

operating environment and the operation timing. It is

Operator Mode

This mode lets you carry out basic operations (ejecting, recording, stopping, rewinding and changing the recording speed mode).

NOTE:

œThis mode will not work correctly unless the VCRs are in the same initial state.

1Press the MENU button to display the MAIN MENU.

2Turn the JOG dial to select the “4.WARNING OUT/CONTR. SET” line, then turn the SHUTTLE ring clockwise.

øThe (WARNING OUT/CONTROL SET) menu appears.

<WARNING@OUT@SET>SET@UP

ALARM@@@@@@@@@@@@Y

NON@REC@@@@@@@@@@N

MECHA.PROBLEM@@@@Y

<CONTROL@SET>

EJECT@MODE@@@@@@@EJECT1

OPERATION@@@@@@@@SLAVE

3Turn the JOG dial until the “OPERATION” setting is highlighted, then turn the SHUTTLE ring clockwise.

4Turn the JOG dial to select the desired operation, then turn the SHUTTLE ring clockwise.

recommended that you check the operating statuses

and menus after carrying out each operation.

Connection

VCR No. 1

VCR No. 2

CONTROL IN COM CONTROL OUT

CONTROL IN COM CONTROL OUT

SLAVE . . . . . . . . . . . . .

MASTER . . . . . . . . . .

The function is restricted to only the VCR being operated.

The function is applied to the VCR being operated and all VCRs that are connected after it.

To CONTROL IN terminal

To COM terminal

œWhen the “OPERATION” is set to “MASTER”, “SC” lights on the digital display.

5Press the MENU EXIT button.

English

41

Page 41 Page 43
Image 42
Page 41 Page 43
Contents SRT-8960 SRT-8168 SRT-8040 Precautions For customers in CanadaLocation PrecautionsMoisture Condensation Problems Avoiding Electrical Shock and FireContents FeaturesAccessory Locations of Controls and Indicators Front PanelOperation Mode Indicator Locations of Controls and IndicatorsOperation Indicators Digital DisplayWith the RS-485/232C interface board Back Panel With the RS-485/232C interface board B C DPower Cord Installation ConnectionsMain Menu Using the JOG dial and Shuttle ring for settingsON-SCREEN Menu Sub-menusON-SCREEN Menu Setting the Language and Clock Language SettingClock setting Setting the Language and Clock Automatic Daylight Saving Time AdjustmentFactory setting Superimpose Display Selecting the Superimpose DisplayChanging the Superimpose Display Position Video Cassette Tapes Video Cassette Tapes Setting the Action to Take When a Cassette is LoadedSetting the Type of Tape Used Correct tape thread check functionIf no tape management data is present on the tape Tape ManagementOperation If tape management data is present on the tapeSetting the Tape Management Function Tape ManagementTape Management menu appears Tape Management Conflict Display Conflict display sampleNormal Recording Recording Speed ModeNormal Recording Before startingRecord Pause Pause/still indicator N flashesNormal Recording Recording CheckSetting the clog detection Action to Take when the Video Signal DeterioratesClog Detection Setting when not using Autorepeat recording Setting the Mode at the End of the TapeSetting the video input signal Setting when using Autorepeat recordingRepeat indicator lights Autorepeat RecordingAutorepeat Recording Alarm Recording Alarm Recording SettingALARM/SERIES REC SET menu appears Alarm Recording Counter Display Alarm RecordingAlarm Recording Reset Function Connections to the Alarm in TerminalAlarm Search Alarm ScanProgram Timer Recording Program Timer Recording Timer SET menu appearsTo Cancel a Program Timer Recording Setting the HolidaysChanging a Program Timer Recording To cancel all program timer recordingsThese portions will not be recorded Recording Using AN External Timer Input Operation Series Recording SetupSeries Recording Loop recordingSingle Image Recording Setup Single Image RecordingNormal Playback Special Playback Special Playback Shuttle Ring OperationDAY/TIME Search Tape CounterDay/Time Search Security Lock Setting the 4 digit security lockCancel the 4 digit security lock Quick Method Security LockClock Adjustment Selecting Input and Output TerminalsConnection Eject output Timer OUT terminal Setting the Cassette Eject ModeCassette Eject Setup Eject input Series in terminalOperator Mode Synchronization ControlSynchronization Control Setting the Cassette Eject ModeAdministrator/Installer Mode SC will flash on the digital displaySetting for RS-485 or RS-232C USE Setting the Address and Data Transfer SpeedSettings when using RS-485 Power FAILURE/DEW/USED Time menu appears Output Terminals Timer OUT terminalTape END OUT Terminal Output Setting Tape END OUT TerminalSW OUT Terminal Output Setting Output TerminalsSW OUT Terminal ALARM@@@@@@@@@@@@Y NON@REC@@@@@@@@@@N Remote control setting Remote JackMaintenance Maintenance Maintenance TableMaintaining and Checking The Mechanism Troubleshooting Guide After a Power FailureSystem Down Connectors SpecificationsGeneral Specifications VideoSpecifications Other SpecificationsConnectors When the Terminal SET is set to SET2 Sanyo Industrial VCR Warranty Weekdays 830 AM 500 PM Pacific Time
Top Page Image Contents