Sharp SRT-8040, SRT-8960, SRT-8168 Back Panel With the RS-485/232C interface board, B C D

Page 8

English

AC power input

L

CONTROL IN terminal

SERIES IN (series recording trigger input) terminal

I

J

K ALARM IN (alarm trigger input) terminal

1 SHOT IN (single image recording trigger input) terminal

œ Signals are output when an alarm, clog detection, video loss, non-recording or mechanism problem occurs.

G COM terminal

H EXT TIMER IN (external timer trigger input) terminal ALARM REST IN (alarm recording reset input) terminal

VIDEO OUT (video output) jack VIDEO IN (video input) jack AUDIO OUT (audio output) jack AUDIO IN (audio input) jack REMOTE (remote control input) jack SW OUT (switch output) terminal

TIMER OUT (timer recording output) terminal TAPE END OUT (tape end output) terminal CONTROL OUT terminal

WARNING OUT (warning output) terminal

1

2

3

4

5

6

7

8

9 F

L

RF4QR/NA (SRT-8960 GB) Wed. May, 08/2002

LOCATIONS OF CONTROLS AND INDICATORS

Back Panel (With the RS-485/232C interface board)

1 A B C D

AC IN

ALARM(1 CONTRO			ES
	S
SH		ERI
	L
OT)	IN	IN

E	(
E	ALAR
XT		M		SE
		TIME		SE
IN			RE
IN		R		T)
				IN

COM

RS232C

A RS485 B

TERMINATE

OFF ON

Do not connect to phone line.

OPEN COLLECTOR(Max. 1=500mA,						2=50mA)
		1		2
	T	T	T	T
	U	U	U	T		T		AUDIO		VIDEO
	O	O	O	U		T
	IN	END		O	O
AR	G			SW		U
AR	ONTROLPE		TIMER	SW			SEE MANUAL
N							SEE MANUAL	IN OUT	IN	OUT
W	C	TA					REMOTE MIC IN

K I G 9 7

J H F 8 6 5 4 3 2 1

1 RS-485/232C interface board (sold separately)

A RS-232C connector (D-sub 9-pin type) B RS-485 A connector (RJ-11)

C RS-485 B connector (RJ-11) D TERMINATE switch

NOTES:

œThe above illustration shows the unit when the RS-485/232C interface board is installed. If no RS-485/232C interface board is installed, connectors and switches A through to D do not appear.

œThe terminal may be damaged by a torque of 0.49

N.m (5kg.cm) or more and by using screwdriver with a tip with a diameter of 6 mm or more.

œDo not connect the RS-485 A and RS-485 B connectors to a phone line.

œThe 7, 9, I and J terminals can be used to select the input and output signals. (Refer to “SELECTING INPUT AND OUTPUT TERMINALS” on page 39.)

œIf using the 9 and J terminals, multiple VCRs can be operated by operating a single VCR. (Refer to “SYNCHRONIZATION CONTROL” on page 41.)

7

Image 8

Contents SRT-8960 SRT-8168 SRT-8040 Precautions For customers in CanadaPrecautions Moisture Condensation ProblemsLocation Avoiding Electrical Shock and FireAccessory ContentsFeatures Locations of Controls and Indicators Front PanelLocations of Controls and Indicators Operation IndicatorsOperation Mode Indicator Digital DisplayWith the RS-485/232C interface board Back Panel With the RS-485/232C interface board B C DPower Cord Installation ConnectionsUsing the JOG dial and Shuttle ring for settings ON-SCREEN MenuMain Menu Sub-menusON-SCREEN Menu Clock setting Setting the Language and ClockLanguage Setting Factory setting Setting the Language and ClockAutomatic Daylight Saving Time Adjustment Changing the Superimpose Display Position Superimpose DisplaySelecting the Superimpose Display Video Cassette Tapes Setting the Action to Take When a Cassette is Loaded Setting the Type of Tape UsedVideo Cassette Tapes Correct tape thread check functionTape Management OperationIf no tape management data is present on the tape If tape management data is present on the tapeTape Management menu appears Setting the Tape Management FunctionTape Management Tape Management Conflict Display Conflict display sampleRecording Speed Mode Normal RecordingNormal Recording Before startingPause/still indicator N flashes Normal RecordingRecord Pause Recording CheckClog Detection Setting the clog detectionAction to Take when the Video Signal Deteriorates Setting the Mode at the End of the Tape Setting the video input signalSetting when not using Autorepeat recording Setting when using Autorepeat recordingAutorepeat Recording Repeat indicator lightsAutorepeat Recording ALARM/SERIES REC SET menu appears Alarm RecordingAlarm Recording Setting Alarm Recording Alarm Recording Reset FunctionAlarm Recording Counter Display Connections to the Alarm in TerminalAlarm Search Alarm ScanProgram Timer Recording Program Timer Recording Timer SET menu appearsSetting the Holidays Changing a Program Timer RecordingTo Cancel a Program Timer Recording To cancel all program timer recordingsThese portions will not be recorded Recording Using AN External Timer Input Series Recording Setup Series RecordingOperation Loop recordingSingle Image Recording Setup Single Image RecordingNormal Playback Special Playback Special Playback Shuttle Ring OperationDay/Time Search DAY/TIME SearchTape Counter Setting the 4 digit security lock Cancel the 4 digit security lockSecurity Lock Quick Method Security LockConnection Clock AdjustmentSelecting Input and Output Terminals Setting the Cassette Eject Mode Cassette Eject SetupEject output Timer OUT terminal Eject input Series in terminalOperator Mode Synchronization ControlSetting the Cassette Eject Mode Administrator/Installer ModeSynchronization Control SC will flash on the digital displaySettings when using RS-485 Setting for RS-485 or RS-232C USESetting the Address and Data Transfer Speed Power FAILURE/DEW/USED Time menu appears Timer OUT terminal Tape END OUT Terminal Output SettingOutput Terminals Tape END OUT TerminalSW OUT Terminal SW OUT Terminal Output SettingOutput Terminals ALARM@@@@@@@@@@@@Y NON@REC@@@@@@@@@@N Remote control setting Remote JackMaintenance Maintaining and Checking The Mechanism MaintenanceMaintenance Table System Down Troubleshooting GuideAfter a Power Failure Specifications General SpecificationsConnectors VideoConnectors When the Terminal SET is set to SET2 SpecificationsOther Specifications Sanyo Industrial VCR Warranty Weekdays 830 AM 500 PM Pacific Time