Sharp SRT-8040, SRT-8960, SRT-8168 instruction manual Normal Playback

Page 35

RF4QR/NA (SRT-8960 GB) Wed. May, 08/2002

NORMAL PLAYBACK

Normal Playback

1Turn on the power to the VCR and TV monitor.

2Load the video cassette tape.

3Press the REC/PLAY SPEED l (or j) button to select the playback speed mode.

øThe selected playback speed mode is displayed on the digital display.

NOTES:

œA slow motion effect or accelerated playback effect can be achieved by using a slower or faster playback speed than the speed used for recording.

œIf the playback speed mode is set to “000”, playback (step 4) will not be possible.

4Press the PLAY button.

øPlayback starts.

øIf necessary, adjust the tracking to eliminate the noise from the picture.

øIf the image is unstable (rolling vertically), adjust the vertical lock control to correct.

5To stop playback, press the STOP button.

øTo advance (or rewind) the tape, turn the SHUTTLE ring clockwise (or counterclockwise).

NOTES:

œA tape recorded on a real time video cassette recorder produced by another manufacturer may not play back with the same degree of clarity on this unit.

œWhen used with a multiplexer in 24- or 40-hour mode playback (or when the “TAPE” in (GENERAL SET) menu is set to “T-120”, in 18- or 30-hour mode playback), the image may roll vertically. In such a case, set “VERTICAL SYNC” to “N” in menu (GENERAL SET) menu.

œWhen a tape recorded with a time lapse VCR is played back, the playback speed mode display and playback time may be different due to the recording speed mode.

Tracking Control

If there is noise in the image during playback,

1While looking at the playback picture, press the TRACKING+ button repeatedly to minimize the noise.

2If it cannot be minimized, press the TRACKING– button repeatedly.

NOTE:

œThis function does not operate when a warning display appears on the digital display.

Vertical Lock Control

During still image mode,

1Press the V. LOCK+ button repeatedly to reduce the vertical rolling of the image.

2If it cannot be corrected, press the V. LOCK– button repeatedly.

NOTE:

œThis function does not operate when a warning display appears on the digital display.

Sharpness Control

1During playback, press and hold the SHARPNESS button for 3 seconds or more.

ø“SH@-:-”appears on the digital display.

2Press the SOFT (or SHARP) button for the desired sharpness of the image.

3When finished, press the SHARPNESS button.

NOTE:

œThis function does not operate when a warning display appears on the digital display.

Audio Playback

œAudio playback is only possible in 8-hour, 24-hour and 40-hour modes (or when the “TAPE” in (GENERAL SET) menu is set to “T-120”, in 6-hour, 18-hour and 30-hour modes).

œThe playback speed has to be the same as the recording speed, for normal playback of the audio.

34

English

Page 34 Page 36
Image 35
Page 34 Page 36
Contents SRT-8960 SRT-8168 SRT-8040 For customers in Canada PrecautionsAvoiding Electrical Shock and Fire PrecautionsMoisture Condensation Problems LocationAccessory ContentsFeatures Front Panel Locations of Controls and IndicatorsDigital Display Locations of Controls and IndicatorsOperation Indicators Operation Mode IndicatorWith the RS-485/232C interface board B C D Back Panel With the RS-485/232C interface boardConnections Power Cord InstallationSub-menus Using the JOG dial and Shuttle ring for settingsON-SCREEN Menu Main MenuON-SCREEN Menu Clock setting Setting the Language and ClockLanguage Setting Factory setting Setting the Language and ClockAutomatic Daylight Saving Time Adjustment Changing the Superimpose Display Position Superimpose DisplaySelecting the Superimpose Display Video Cassette Tapes Correct tape thread check function Setting the Action to Take When a Cassette is LoadedSetting the Type of Tape Used Video Cassette TapesIf tape management data is present on the tape Tape ManagementOperation If no tape management data is present on the tapeTape Management menu appears Setting the Tape Management FunctionTape Management Conflict display sample Tape Management Conflict DisplayBefore starting Recording Speed ModeNormal Recording Normal RecordingRecording Check Pause/still indicator N flashesNormal Recording Record PauseClog Detection Setting the clog detectionAction to Take when the Video Signal Deteriorates Setting when using Autorepeat recording Setting the Mode at the End of the TapeSetting the video input signal Setting when not using Autorepeat recordingAutorepeat Recording Repeat indicator lightsAutorepeat Recording ALARM/SERIES REC SET menu appears Alarm RecordingAlarm Recording Setting Connections to the Alarm in Terminal Alarm RecordingAlarm Recording Reset Function Alarm Recording Counter DisplayAlarm Scan Alarm SearchProgram Timer Recording Timer SET menu appears Program Timer RecordingTo cancel all program timer recordings Setting the HolidaysChanging a Program Timer Recording To Cancel a Program Timer RecordingThese portions will not be recorded Recording Using AN External Timer Input Loop recording Series Recording SetupSeries Recording OperationSingle Image Recording Single Image Recording SetupNormal Playback Special Playback Shuttle Ring Operation Special PlaybackDay/Time Search DAY/TIME SearchTape Counter Quick Method Security Lock Setting the 4 digit security lockCancel the 4 digit security lock Security LockConnection Clock AdjustmentSelecting Input and Output Terminals Eject input Series in terminal Setting the Cassette Eject ModeCassette Eject Setup Eject output Timer OUT terminalSynchronization Control Operator ModeSC will flash on the digital display Setting the Cassette Eject ModeAdministrator/Installer Mode Synchronization ControlSettings when using RS-485 Setting for RS-485 or RS-232C USESetting the Address and Data Transfer Speed Power FAILURE/DEW/USED Time menu appears Tape END OUT Terminal Timer OUT terminalTape END OUT Terminal Output Setting Output TerminalsSW OUT Terminal SW OUT Terminal Output SettingOutput Terminals ALARM@@@@@@@@@@@@Y NON@REC@@@@@@@@@@N Remote Jack Remote control settingMaintenance Maintaining and Checking The Mechanism MaintenanceMaintenance Table System Down Troubleshooting GuideAfter a Power Failure Video SpecificationsGeneral Specifications ConnectorsConnectors When the Terminal SET is set to SET2 SpecificationsOther Specifications Weekdays 830 AM 500 PM Pacific Time Sanyo Industrial VCR Warranty
Top Page Image Contents