Sharp SRT-8040, SRT-8960, SRT-8168 Setting the Cassette Eject Mode, Cassette Eject Setup

Page 41

RF4QR/NA (SRT-8960 GB) Wed. May, 08/2002

SETTING THE CASSETTE EJECT MODE

Cassette Eject Setup

When using two or more VCRs, the cassette tapes of all the VCRs or some of the VCRs can be ejected at the same time.

NOTE:

œ“TERMINAL SET” in the (OTHERS) menu should always be set to “SET2”.

1Press the MENU button to display the MAIN MENU.

2Turn the JOG dial to select the “4.WARNING OUT/CONTR. SET” line, then turn the SHUTTLE ring clockwise.

øThe (WARNING OUT/CONTROL SET) menu appears.

<WARNING@OUT@SET>SET@UP

ALARM@@@@@@@@@@@@Y

NON@REC@@@@@@@@@@N

MECHA.PROBLEM@@@@Y

<CONTROL@SET>

EJECT@MODE@@@@@@@EJECT1

OPERATION@@@@@@@@SLAVE

3Turn the JOG dial until the “EJECT MODE” setting is highlighted, then turn the SHUTTLE ring clockwise.

4Turn the JOG dial to select the desired cassette eject mode, then turn the SHUTTLE ring clockwise.

EJECT1 . . . . The cassette is ejected only if the VCR is not in recording or recording pause mode.

EJECT2 . . . . The cassette is ejected only if the VCR is in stop mode.

5Turn the JOG dial until the “OPERATION” setting is highlighted, then turn the SHUTTLE ring clockwise.

6Turn the JOG dial to select the desired operation, then turn the SHUTTLE ring clockwise.

SLAVE . . . . . The function is restricted to only the VCR being operated.

MASTER . . . The function is applied to the VCR being operated and all VCRs that are connected after it.

7Press the MENU EXIT button.

NOTE:

œThe EJECT button will not be operative during recording mode.

Connection

VCR No. 1	VCR No. 2
SERIES IN COM TIMER OUT	SERIES IN COM TIMER OUT

To SERIES IN terminal

To COM terminal

Eject input (SERIES IN) terminal

œDepending on the “EJECT MODE” setting in the (WARNING OUT/CONTROL SET) menu (see “Cassette Eject Setup”), the cassette loaded into the VCR can be ejected when there is input to this terminal.

Eject output (TIMER OUT) terminal

œA signal is output from this terminal when the EJECT button is pressed (if the VCR is set up as the “MASTER” VCR; see step 6 under “Cassette Eject Setup”) or when there is input (a trigger) at the SERIES IN terminal, even if the security lock is set or a cassette is not loaded.

NOTES:

œThe terminal names and signals are different from the usual setting.

œNames in brackets apply to terminals on the rear panel.

40

English

Image 41

Contents SRT-8960 SRT-8168 SRT-8040 For customers in Canada PrecautionsMoisture Condensation Problems PrecautionsLocation Avoiding Electrical Shock and FireAccessory ContentsFeatures Front Panel Locations of Controls and IndicatorsOperation Indicators Locations of Controls and IndicatorsOperation Mode Indicator Digital DisplayWith the RS-485/232C interface board B C D Back Panel With the RS-485/232C interface boardConnections Power Cord InstallationON-SCREEN Menu Using the JOG dial and Shuttle ring for settingsMain Menu Sub-menusON-SCREEN Menu Clock setting Setting the Language and ClockLanguage Setting Factory setting Setting the Language and ClockAutomatic Daylight Saving Time Adjustment Changing the Superimpose Display Position Superimpose DisplaySelecting the Superimpose Display Video Cassette Tapes Setting the Type of Tape Used Setting the Action to Take When a Cassette is LoadedVideo Cassette Tapes Correct tape thread check functionOperation Tape ManagementIf no tape management data is present on the tape If tape management data is present on the tapeTape Management menu appears Setting the Tape Management FunctionTape Management Conflict display sample Tape Management Conflict DisplayNormal Recording Recording Speed ModeNormal Recording Before startingNormal Recording Pause/still indicator N flashesRecord Pause Recording CheckClog Detection Setting the clog detectionAction to Take when the Video Signal Deteriorates Setting the video input signal Setting the Mode at the End of the TapeSetting when not using Autorepeat recording Setting when using Autorepeat recordingAutorepeat Recording Repeat indicator lightsAutorepeat Recording ALARM/SERIES REC SET menu appears Alarm RecordingAlarm Recording Setting Alarm Recording Reset Function Alarm RecordingAlarm Recording Counter Display Connections to the Alarm in TerminalAlarm Scan Alarm SearchProgram Timer Recording Timer SET menu appears Program Timer RecordingChanging a Program Timer Recording Setting the HolidaysTo Cancel a Program Timer Recording To cancel all program timer recordingsThese portions will not be recorded Recording Using AN External Timer Input Series Recording Series Recording SetupOperation Loop recordingSingle Image Recording Single Image Recording SetupNormal Playback Special Playback Shuttle Ring Operation Special PlaybackDay/Time Search DAY/TIME SearchTape Counter Cancel the 4 digit security lock Setting the 4 digit security lockSecurity Lock Quick Method Security LockConnection Clock AdjustmentSelecting Input and Output Terminals Cassette Eject Setup Setting the Cassette Eject ModeEject output Timer OUT terminal Eject input Series in terminalSynchronization Control Operator ModeAdministrator/Installer Mode Setting the Cassette Eject ModeSynchronization Control SC will flash on the digital displaySettings when using RS-485 Setting for RS-485 or RS-232C USESetting the Address and Data Transfer Speed Power FAILURE/DEW/USED Time menu appears Tape END OUT Terminal Output Setting Timer OUT terminalOutput Terminals Tape END OUT TerminalSW OUT Terminal SW OUT Terminal Output SettingOutput Terminals ALARM@@@@@@@@@@@@Y NON@REC@@@@@@@@@@N Remote Jack Remote control settingMaintenance Maintaining and Checking The Mechanism MaintenanceMaintenance Table System Down Troubleshooting GuideAfter a Power Failure General Specifications SpecificationsConnectors VideoConnectors When the Terminal SET is set to SET2 SpecificationsOther Specifications Weekdays 830 AM 500 PM Pacific Time Sanyo Industrial VCR Warranty